Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY BLOWER

BATTERY BLOWER > INSTALLATION

for Preparation Click here



1. INSTALL BATTERY COOLING BLOWER ASSEMBLY

NOTICE:
  1. Be sure not to touch the fan part of the battery cooling blower assembly.
  2. Do not lift the battery cooling blower assembly using the wire harness.

  1. Install the battery cooling blower assembly with the nut and 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the battery cooling blower assembly connector and engage the clamp.



2. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B296198
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



3. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B392248E01
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
    Text in Illustration 
    *a
    Hook



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



4. INSTALL FRONT CENTER FLOOR COVER (for Separate Type Seatback)
  1. Engage the 2 guides to install the front center floor cover.

  1. Install the 3 clips.



5. INSTALL FRONT CENTER FLOOR COVER (for Bench Type Seatback)
  1. Engage the 2 guides to install the front center floor cover.

  1. Install the 3 clips.



6. INSTALL FRONT FLOOR COVER LH (for Separate Type Seatback)
  1. Engage the 3 guides.



    B301490E01
  1. Engage the clip <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



7. INSTALL FRONT FLOOR COVER LH (for Bench Type Seatback)
  1. Engage the 3 guides.



    B301490E01
  1. Engage the clip <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



8. INSTALL FRONT FLOOR COVER RH (for Separate Type Seatback)
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



9. INSTALL FRONT FLOOR COVER RH (for Bench Type Seatback)
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



10. CLEAR DTC

HINT:
If the message "COOLING PERFORMANCE OF THE HYBRID BATTERY IS LOW VISIT YOUR DEALER" is displayed on the multi-information display, clean or replace the battery cooling blower assembly, and clear the DTCs to reset the learning values even if no DTCs are output (Click here).