Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > CALIBRATION

for Preparation Click here



TORQUE SENSOR ZERO POINT CALIBRATION (USING THE INTELLIGENT TESTER)

NOTICE:
Perform torque sensor zero point calibration if any of the following conditions occur:
  1. The power steering ECU assembly has been replaced.
  2. The electric power steering column sub-assembly has been replaced.
  3. There is a difference in steering effort between turning left and right.

  1. Inspection before calibration

    1. Turn the power switch off (lock).

    2. Connect the intelligent tester to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the intelligent tester on.

    5. Calibrate the power steering ECU assembly. Enter the following menus: Chassis / EMPS / Data List.

    6. Check the values by referring to the table below.

      EMPS 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      IG Power Supply
      ECU power source voltage/
      Min.: 0.0000V
      Max.: 20.1531 V
      9 to 16 V
      Power switch on (IG)

      Standard Voltage:
      9 to 16 V

      NOTICE:
      If the IG power supply voltage is 9 V or less, calibration cannot be performed. In this case, charge or replace the auxiliary battery, and then perform calibration.

  2. Torque sensor zero point calibration

    NOTICE:
    If DTC C1516/16 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTCs before starting calibration.


    1. Set the steering wheel to the center point and align the front wheels straight ahead.

    2. Turn the power switch off (lock).

    3. Connect the intelligent tester to the DLC3.

    4. Turn the power switch on (IG).

    5. Turn the intelligent tester on.

    6. Enter the following menus: Chassis / EMPS / Utility / Torque Sensor Adjustment.

      NOTICE:
      1. Do not turn the steering wheel sharply.
      2. Do not touch the steering wheel during torque sensor zero point calibration (for 3 seconds).

    7. Check for DTCs (Click here).

      NOTICE:
      If DTC C1515/15, C1516/16, C1534/34 or C1581/81 is output, perform troubleshooting for the corresponding DTC.

      Result:
      Result
      See Procedure
      DTC C1515/15 is output.
      Click here
      DTC C1516/16 is output.
      Click here
      DTC C1534/34 is output.
      Click here
      DTC C1581/81 is output.
      Click here


TORQUE SENSOR ZERO POINT CALIBRATION (USING SST CHECK WIRE)

NOTICE:
Calibrate the torque sensor zero point if any of the following has occurred:
  1. The power steering ECU assembly has been replaced.
  2. The electric power steering column sub-assembly has been replaced.
  3. Steering effort differs between left and right.

  1. Check for DTCs.

    1. Check for DTCs (Click here).

      NOTICE:
      1. If DTC C1516/16 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTC before starting calibration.
      2. If DTCs other than C1516/16 is output, refer to the "Diagnostic Trouble Code Chart" (Click here).



  2. Perform pre-calibration check.

    1. Turn the power switch off (lock).

    2. Disconnect the G6 power steering ECU assembly connector.

    3. Turn the power switch on (IG).



    4. C261922E01
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G6-1 (IG) - Body ground
      Power switch on (IG)
      9 to 16 V

      NOTICE:
      If the IG power supply voltage is 9 V or less, calibration cannot be performed. In this case, charge or replace the auxiliary battery, and then perform calibration.

    6. Turn the power switch off (lock).

    7. Connect the G6 power steering ECU assembly connector.
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Steering ECU Assembly)



  3. Clear sensor calibration value.

    1. Set the steering wheel to the center point and align the front tires straight ahead.

    2. Turn the power switch off (lock).



    3. C248264E03
    4. Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Connect the terminals to the correct positions to avoid a malfunction.

      Text in Illustration 
      *1
      DLC3



    5. Turn the power switch on (IG) and then connect and disconnect terminals 13 (TC) and 4 (CG) at least 20 times in 20 seconds.


      C143546E16


      Text in Illustration (Clearing Sensor Calibration Value) 
      *1
      DLC3 (TS and CG)
      *2
      Power Switch
      *3
      DLC3 (TC and CG)
      *4
      EPS Warning Light
      *a
      Short
      *b
      Open
      *c
      on (IG)
      *d
      off (lock)
      *e
      ON
      *f
      OFF
      *g
      20 Times Or More
      *h
      0.125 Seconds
      *i
      20 Seconds




    6. C213288E02
    7. Check that the EPS warning light blinks and then remains illuminated.

      HINT:
      The EPS warning light illumination indicates that DTCs C1515/15 has been stored.

    8. Turn the power switch off (lock).

      NOTICE:
      After erasing the sensor calibration value zero point calibration cannot be performed if the power switch is on (IG).

      Text in Illustration 
      *1
      EPS Warning Light



  4. Perform torque sensor zero point calibration.

    NOTICE:
    As torque sensor zero point calibration cannot be performed if DTC C1515/15 has not been stored, be sure to perform sensor calibration value erasure before performing torque sensor zero point calibration.


    1. Set the steering wheel to the center point and align the front tires straight ahead.

    2. Turn the power switch off (lock).



    3. C248264E03
    4. Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

      SST
      09843-18040  
      Text in Illustration 
      *1
      DLC3

    5. Turn the power switch on (IG) and then connect terminals 13 (TC) and 4 (CG).

      NOTICE:
      Do not touch the steering wheel during calibration (for 3 seconds).

      HINT:
      The EPS warning light remains illuminated even after calibration has completed.

    6. With terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) connected, and the power switch on (IG), continue to perform rotation angle sensor initialization.


ASSIST MAP WRITING (USING THE INTELLIGENT TESTER)

NOTICE:
Perform assist map writing if any of the following conditions occur:
  1. The power steering ECU assembly has been replaced.

  1. Turn the power switch off (lock).

  2. Connect the intelligent tester to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the intelligent tester on.

  5. Enter the following menus: Chassis / EMPS / Utility / Signal Check.

    HINT:
    1. Follow the instructions on the intelligent tester to perform Signal Check.
    2. With DTC C1581/81 output, performing Signal Check will cause the power steering ECU assembly to enter Test Mode and the assist map will be written automatically.

  6. Wait for at least 5 seconds.

  7. Check for DTCs (Click here).

    HINT:
    After writing the assist map, if DTC C1581/81 is output, perform the troubleshooting procedure for DTC C1581/81 (Click here).


ASSIST MAP WRITING (USING SST CHECK WIRE)

NOTICE:
Perform assist map writing if any of the following conditions occur:
  1. The power steering ECU assembly has been replaced.

HINT:
If DTC C1581/81 is output after torque sensor zero point calibration, perform assist map writing.



    C248264E03
  1. Turn the power switch off (lock).
    Text in Illustration 
    *1
    DLC3

  2. Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

    SST
    09843-18040  

    NOTICE:
    Connect the terminals correctly to avoid a malfunction.

  3. Turn the power switch on (IG).

  4. Wait for 5 seconds or more.

  5. Check for DTCs (Click here).

    HINT:
    After writing the assist map, if DTC C1581/81 is output, perform the troubleshooting procedure for DTC C1581/81 (Click here).