POWER STEERING SYSTEM > CALIBRATION |
| TORQUE SENSOR ZERO POINT CALIBRATION (USING THE INTELLIGENT TESTER) |
Inspection before calibration
Turn the power switch off (lock).
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Calibrate the power steering ECU assembly. Enter the following menus: Chassis / EMPS / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| IG Power Supply | ECU power source voltage/ Min.: 0.0000V Max.: 20.1531 V | 9 to 16 V | Power switch on (IG) |
Torque sensor zero point calibration
Set the steering wheel to the center point and align the front wheels straight ahead.
Turn the power switch off (lock).
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / EMPS / Utility / Torque Sensor Adjustment.
Check for DTCs (Click here).
| Result | See Procedure |
| DTC C1515/15 is output. |
Click here
|
| DTC C1516/16 is output. |
Click here
|
| DTC C1534/34 is output. |
Click here
|
| DTC C1581/81 is output. |
Click here
|
| TORQUE SENSOR ZERO POINT CALIBRATION (USING SST CHECK WIRE) |
Check for DTCs.
Check for DTCs (Click here).
Perform pre-calibration check.
Turn the power switch off (lock).
Disconnect the G6 power steering ECU assembly connector.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G6-1 (IG) - Body ground | Power switch on (IG) | 9 to 16 V |
Turn the power switch off (lock).
Connect the G6 power steering ECU assembly connector.
| *a | Front view of wire harness connector (to Power Steering ECU Assembly) |
Clear sensor calibration value.
Set the steering wheel to the center point and align the front tires straight ahead.
Turn the power switch off (lock).
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Turn the power switch on (IG) and then connect and disconnect terminals 13 (TC) and 4 (CG) at least 20 times in 20 seconds.

| *1 | DLC3 (TS and CG) | *2 | Power Switch |
| *3 | DLC3 (TC and CG) | *4 | EPS Warning Light |
| *a | Short | *b | Open |
| *c | on (IG) | *d | off (lock) |
| *e | ON | *f | OFF |
| *g | 20 Times Or More | *h | 0.125 Seconds |
| *i | 20 Seconds |
![]() |
Check that the EPS warning light blinks and then remains illuminated.
Turn the power switch off (lock).
| *1 | EPS Warning Light |
Perform torque sensor zero point calibration.
Set the steering wheel to the center point and align the front tires straight ahead.
Turn the power switch off (lock).
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Turn the power switch on (IG) and then connect terminals 13 (TC) and 4 (CG).
With terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) connected, and the power switch on (IG), continue to perform rotation angle sensor initialization.
| ASSIST MAP WRITING (USING THE INTELLIGENT TESTER) |
Turn the power switch off (lock).
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / EMPS / Utility / Signal Check.
Wait for at least 5 seconds.
Check for DTCs (Click here).
| ASSIST MAP WRITING (USING SST CHECK WIRE) |
![]() |
Turn the power switch off (lock).
| *1 | DLC3 |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the power switch on (IG).
Wait for 5 seconds or more.
Check for DTCs (Click here).