Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even if the values are within specifications.
  2. Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.

  1. Turn the power switch off (lock).

  2. Connect the intelligent tester to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the intelligent tester on.

  5. Check the freeze frame data on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter/
    Min.: 0.0 km/h (0.0mph)
    Max.: 300.0 km/h (186.4 mph)
    0 km/h (0 mph)
    Power switch on (ready) and vehicle stopped
    No significant fluctuation
    Power switch on (ready) and vehicle driven at constant speed
    Motor Actual Current
    Current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    -The value increases when turning right and decreases when turning left
    Power switch on (ready) and steering wheel being turned
    Command Value Current
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    -The value increases when turning right and decreases when turning left
    Power switch on (ready) and steering wheel being turned
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -50.0°C (-58.0°F)
    Max.: 150.0°C (302.0°F)
    -50 to 150°C (-58 to 302°F)
    -
    PIG Power Supply
    Power source voltage to activate motor/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Always
    IG Power Supply
    ECU power source voltage/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Power switch on (IG)
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -327.68 Nm
    Max.: 7.00 Nm
    Value changes in proportion to steering effort
    -The value increases when turning left and decreases when turning right
    Power switch on (ready) and steering wheel being turned
    Torque Sensor 1 Output
    Torque sensor 1 output value/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Power switch on (ready) and steering wheel not being turned (without load)
    2.5 to 3.8 V
    Power switch on (ready) and steering wheel being turned to right with vehicle stopped
    1.2 to 2.5 V
    Power switch on (ready) and steering wheel being turned to left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor 2 output value/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Power switch on (ready) and steering wheel not being turned (without load)
    1.2 to 2.5 V
    Power switch on (ready) and steering wheel being turned to right with vehicle stopped
    2.5 to 3.8 V
    Power switch on (ready) and steering wheel being turned to left with vehicle stopped
    TRQ1 Zero Point Value
    Zero point value of torque sensor 1/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Power switch on (ready) and steering wheel not being turned (without load)
    TRQ2 Zero Point Value
    Zero point value of torque sensor 2/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Power switch on (ready) and steering wheel not being turned (without load)
    Motor Terminal Volt(+)
    Motor terminal M1 voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    9 to 16 V
    Power switch on (ready) and steering wheel being turned to right
    6 to 8 V
    Power switch on (ready) and steering wheel being turned to left
    Motor Terminal Volt(-)
    Motor terminal M2 voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    6 to 8 V
    Power switch on (ready) and steering wheel being turned to right
    9 to 16 V
    Power switch on (ready) and steering wheel being turned to left
    Ready Status
    Ready status/
    Ready or OFF
    READY or OFF
    -