SFI SYSTEM > ECM Power Source Circuit |

| 1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C10-16 (E1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C9-16 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-37 (IGSW) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | |
| 3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY) |
Inspect the No. 1 integration relay (EFI MAIN relay) (Click here).
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM) |
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2C-4 - A40-2 (+B) | Always | Below 1 Ω |
| 2C-4 - A40-3 (+B2) | Always | Below 1 Ω |
| 2C-3 - A40-46 (MREL) | Always | Below 1 Ω |
| 2C-4 or A40-2 (+B) - Body ground | Always | 10 kΩ or higher |
| 2C-4 or A40-3 (+B2) - Body ground | Always | 10 kΩ or higher |
| 2C-3 or A40-46 (MREL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY) |
![]() |
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2E-1 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to No. 1 Integration Relay) |
|
| ||||
| OK | ||
| ||
| 6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY) |
Inspect the No. 1 integration relay (IG2 relay) (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM) |
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-4 - A40-37 (IGSW) | Always | Below 1 Ω |
| 2D-4 or A40-37 (IGSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY) |
![]() |
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2E-1 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to No. 1 Integration Relay) |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND) |
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INTEGRATION RELAY) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G77-9 (IG2D) - 2D-3 | Always | Below 1 Ω |
| G77-9 (IG2D) or 2D-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||