Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Certification ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Certification ECU Communication Stop Mode
Either condition is met:
  1. "Certification (Smart)" is not displayed on the CAN Bus Check screen of the GTS (Click here).
  2. Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output (Click here).
  1. Smart key ECU assembly (Certification ECU) branch line or connector
  2. Power source circuit of smart key ECU assembly (certification ECU)
  3. Smart key ECU assembly (Certification ECU) ground circuit
  4. Smart key ECU assembly (Certification ECU)

WIRING DIAGRAM


C260978E10


C251626E07


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.
  6. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).
  7. Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) BRANCH LINE)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C240536E09
  1. Disconnect the G79 smart key ECU assembly (certification ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G79-14 (CANH) - G79-15 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Smart Key ECU Assembly (Certification ECU))



NG
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU))
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the G77 smart key ECU assembly (certification ECU) connector.



    C240538E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G77-11 (E) - Body ground
    Cable disconnected from negative (-) auxiliary battery terminal
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Smart Key ECU Assembly (Certification ECU))

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G77-2 (+B) - Body ground
    Power switch off
    11 to 14 V
    G79-5 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)