Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0AFC-150    Hybrid Battery Pack Sensor Module

for Preparation Click here


DESCRIPTION

The hybrid vehicle control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC NO.
INF Code
DTC Detection Condition
Trouble Area
P0AFC
150
Power source voltage of the battery smart unit drops during precharge.
  1. Battery smart unit
  2. Wire harness or connector

WIRING DIAGRAM


A279685E07


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
  1. After completing repairs, restart the system (turn the power switch on (READY)) and recheck for DTCs (Click here).
  2. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Turn the power switch on (READY) and wait for 15 seconds or more.

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid battery exhaust duct .

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).



    A260174E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M39-3 (IGCT) - M39-6 (GND)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Smart Unit)

NOTICE:
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the No. 1 hybrid battery exhaust duct.



NG
Go to step 2
OK

REPLACE BATTERY SMART UNIT (Click here)  

2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid battery exhaust duct .



    A260174E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M39-6 (GND) - Body ground
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Smart Unit)

  1. Install the No. 1 hybrid battery exhaust duct.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATT VL SSR FUSE - BATTERY SMART UNIT)