Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A10-592    DC / DC Converter Status Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A09-591 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A10
592
DC/DC converter voltage switching (VLO) signal circuit malfunction (short to +B)
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. Hybrid vehicle control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A09-591 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 10 seconds or more.

1.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.

  1. Turn the power switch on (IG).



    A217247E17
  1. Measure the waveform.
    Item
    Content
    Terminal
    A71-16 (VLO) - G80-6 (E1)
    Equipment Setting
    5 V/DIV., 50 ms/DIV.
    Condition
    Power switch on (IG)
    Text in Illustration 
    *a
    Component with harness connected
    (Hybrid Vehicle Control ECU)

    OK:
    The waveform appears as shown in the illustration.

    HINT:
    1. Perform this inspection with the hybrid vehicle control ECU connector connected.

  1. Turn the power switch off.



NG
Go to step 5
OK


2.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


3.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A10-592 is not output.
    A
    P0A10-592 is output again.
    B

  1. Turn the power switch off.



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


4.CHECK FOR INTERMITTENT PROBLEMS
(Click here)


NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A71 from the hybrid vehicle control ECU.

  1. Disconnect connector A47 from the inverter with converter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).



    A216618E40
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-3 (VLO) or A71-16 (VLO) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)

    NOTICE:
    Turning the power switch on (IG) with the inverter with converter assembly connector and the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the inverter with converter assembly connector.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE HYBRID VEHICLE CONTROL ECU
(Click here)

NEXT


7.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


8.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A10-592 is not output.
    A
    P0A10-592 is output again.
    B

  1. Turn the power switch off.



B
REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)
A

COMPLETED