Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0516-769    Battery Temperature Sensor Circuit Low

DTC    P0517-770    Battery Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION


  1. The battery thermometer sensor detects the auxiliary battery temperature. The resistance of the battery thermometer sensor built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the battery thermometer sensor resistance. Conversely, the higher the temperature, the lower the resistance. The battery thermometer sensor is connected to the hybrid vehicle control ECU. A voltage of 5 V is supplied to the battery thermometer sensor from the THB terminal of the hybrid vehicle control ECU through its internal resistor R. This means that resistor R and the battery thermometer sensor are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the hybrid vehicle control ECU reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.

    HINT:
    Characteristics of the battery thermometer sensor resistance (reference values) are as follows.

    Terminal
    THB
    (with Connector Disconnected)
    Resistance
    Ambient Temperature
    THB - E2
    4.5 to 5.5 V
    3.00 to 3.73 kΩ
    Approximately 10°C (50°F)
    1.60 to 1.80 kΩ
    Approximately 25°C (77°F)
    0.80 to 1.00 kΩ
    Approximately 40°C (104°F)



    A266952E01


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0516
769
Malfunction in the battery thermometer sensor circuit (short to GND)
  1. Battery thermometer sensor
  2. Wire harness or connector
  3. Hybrid vehicle control ECU
P0517
770
Malfunction in the battery thermometer sensor circuit (open or short to +B)

WIRING DIAGRAM


A259938E24


INSPECTION PROCEDURE

HINT:
  1. Read the freeze frame data using the intelligent tester. In the freeze frame data, some information is recorded about the vehicle conditions at the moment a malfunction occurred. This information can be helpful when troubleshooting.
  2. After confirming that DTC P0516-769 or P0517-770 is output, use the intelligent tester to check "Auxiliary Batt Temperature" in the Hybrid Control Data List.

    Displayed Temperature
    Malfunction
    -40°C (-40°F)
    Open circuit or short to +B
    215°C (419°F)
    Short circuit or short to GND
  3. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Turn the power switch on (IG) and wait for 5 seconds or more.

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A279820E01
  1. Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors (Click here).
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


2.READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    Result:
    Result
    Proceed to
    -40°C (-40°F)
    A
    215°C (419°F)
    B
    Same as actual temperature
    C

  1. Turn the power switch off.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)


    A267463
  1. Disconnect connector M43 from the battery thermometer sensor.



    A237420E09
  1. Connect terminals 2 (THB) and 1 (E2) of vehicle side connector M43 of the battery thermometer sensor.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Auxiliary Batt Temperature
    Terminals THB and E2 connected.
    Power switch on (IG)
    215°C (419°F)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Thermometer Sensor)

  1. Turn the power switch off.

  1. Connect the battery thermometer sensor connector.



NG
Go to step 4
OK

REPLACE BATTERY THERMOMETER SENSOR 

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY THERMOMETER SENSOR)


    A249750E43
  1. Connect terminals 20 (THB) and 21 (ETHB) of connector G81 of the hybrid vehicle control ECU.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Auxiliary Batt Temperature
    Terminals THB and ETHB connected.
    Power switch on (IG)
    215°C (419°F)

    Text in Illustration 
    *a
    Component with harness connected
    (Hybrid Vehicle Control ECU)

  1. Turn the power switch off.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)


    A267463
  1. Disconnect connector M43 from the battery thermometer sensor.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

  1. Read the Data List.

    OK:
    Tester Display
    Switch Condition
    Specified Condition
    Auxiliary Batt Temperature
    Power switch on (IG)
    -40°C (-40°F)

  1. Turn the power switch off.

  1. Connect the battery thermometer sensor connector.



NG
Go to step 6
OK

REPLACE BATTERY THERMOMETER SENSOR 

6.CHECK HARNESS AND CONNECTOR (BATTERY THERMOMETER SENSOR - HYBRID VEHICLE CONTROL ECU)
  1. Disconnect connector M43 from the battery thermometer sensor.

  1. Disconnect connector G81 from the hybrid vehicle control ECU.



    A344219E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    M43-2 (THB) - G81-20 (THB)
    Power switch off
    Below 1 Ω
    M43-1 (E2) - G81-21 (ETHB)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    M43-2 (THB) or G81-20 (THB)- Body ground and other terminals
    Power switch off
    10 kΩ or higher
    M43-1 (E2) or G81-21 (ETHB)- Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Thermometer Sensor)
    *b
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)

  1. Connect the battery thermometer sensor connector.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)