Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > DISASSEMBLY

for Preparation Click here



1. REMOVE HEADLIGHT CLEANER WASHER NOZZLE COVER (w/ Headlight Cleaner System)


    E237629
  1. Extend the headlight cleaner washer nozzle.

  1. Disengage the 2 claws and remove the headlight cleaner washer nozzle cover.

    HINT:
    Use the same procedure for the RH side and LH side.



2. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E237621E01
  1. Push the tabs shown by arrows (a) and (b) and disconnect the headlight cleaner hose.



    E237622
  1. Remove the headlight cleaner clamp as shown in the illustration.



    E237624E01
  1. Pull down the headlight cleaner actuator clamp as shown in the illustration.
    Text in Illustration 
    *1
    Headlight Cleaner Actuator Clamp



  1. While pushing the tab shown by arrow (a), disengage the claw and guide to remove the headlight washer actuator sub-assembly LH as shown in the illustration.


    E237626E01



3. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure for the RH side and LH side.



4. REMOVE HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


    B297131
  1. Disengage the 7 clamps and remove the headlight cleaner hose.



5. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET


    B310574
  1. Remove the 2 screws.

  1. Disengage the 2 claws and remove the front bumper extension mounting bracket.



6. REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY LH


    E237707
  1. Remove the bolt.

  1. Disengage the 2 claws and remove the front turn signal light assembly.



7. REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE FOG LIGHT ASSEMBLY LH


    E237703
  1. Remove the screw.

  1. Disengage the 2 guides and remove the fog light assembly.



9. REMOVE FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE FOG LIGHT COVER LH


    B297132
  1. Disengage the 6 claws and remove the fog light cover LH.



11. REMOVE FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



12. REMOVE HOOD TO FRONT END PANEL SEAL


    B297134
  1. Remove the 3 clips and hood to front end panel seal.



13. REMOVE UPPER FRONT BUMPER RETAINER


    B297133
  1. Remove the 4 clips and remove the upper front bumper retainer.



14. REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


    B297138
  1. Remove the 2 screws.

  1. Disengage the 4 claws and 2 guides, and remove the radiator grill (or front panel) emblem.



15. REMOVE RADIATOR GRILLE


    B297135
  1. Disengage the 12 claws and remove the radiator grille.



16. REMOVE LOWER NO. 1 RADIATOR GRILLE


    B297136
  1. Disengage the 16 claws and remove the lower No. 1 radiator grille.



17. REMOVE FRONT BUMPER HOLE COVER


    B297137
  1. Disengage the 2 claws and remove the front bumper hole cover.



18. REMOVE FRONT BUMPER SIDE RETAINER LH


    B310558
  1. Remove the bolt.

  1. Disengage the claw and remove the front bumper side retainer LH.



19. REMOVE FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



20. REMOVE RADIATOR SUPPORT OPENING COVER


    B297147
  1. Remove the 4 clips and remove the radiator support opening cover.



21. REMOVE NO. 2 RADIATOR SIDE AIR SEAL


    B307338
  1. Disengage the 2 claws and remove the No. 2 radiator side air seal.



22. REMOVE NO. 1 RADIATOR SIDE AIR SEAL


    B307339
  1. Disengage the 2 claws and remove the No. 1 radiator side air seal.



23. REMOVE RADIATOR SUPPORT EXTENSION LH


    B307340
  1. Disengage the 2 clamps and disconnect the thermistor assembly.

  1. Disengage the 2 claws and remove the radiator support extension LH.



24. REMOVE RADIATOR SUPPORT EXTENSION RH


    B307341
  1. Disengage the 2 claws and remove the radiator support extension RH.



25. REMOVE FRONT BUMPER ENERGY ABSORBER


    B310562
  1. Disengage the 2 guides to remove the front bumper energy absorber.



26. REMOVE FRONT BUMPER REINFORCEMENT


    B310563
  1. Disengage the 2 clamps and disconnect the wire harness.

  1. Remove the 6 bolts and front bumper reinforcement.