FRONT BUMPER > REASSEMBLY |
| 1. INSTALL FRONT BUMPER REINFORCEMENT |
![]() |
Install the front bumper reinforcement with the 6 bolts.
Engage the 2 clamps and install the wire harness.
| 2. INSTALL FRONT BUMPER ENERGY ABSORBER |
![]() |
Engage the 2 guides to install the front bumper energy absorber.
| 3. INSTALL RADIATOR SUPPORT EXTENSION LH |
![]() |
Engage the 2 claws and install the radiator support extension LH.
Engage the 2 clamps to install the thermistor assembly.
| 4. INSTALL RADIATOR SUPPORT EXTENSION RH |
![]() |
Engage the 2 claws and install the radiator support extension RH.
| 5. INSTALL NO. 2 RADIATOR SIDE AIR SEAL |
![]() |
Engage the 2 claws and install the No. 2 radiator side air seal.
| 6. INSTALL NO. 1 RADIATOR SIDE AIR SEAL |
![]() |
Engage the 2 claws and install the No. 1 radiator side air seal.
| 7. INSTALL RADIATOR SUPPORT OPENING COVER |
![]() |
Install the radiator support opening cover with the 4 clips.
| 8. INSTALL FRONT BUMPER SIDE RETAINER LH |
![]() |
Engage the 2 claws.
![]() |
Install the front bumper side retainer LH with the bolt.
| 9. INSTALL FRONT BUMPER SIDE RETAINER RH |
| 10. INSTALL RADIATOR GRILLE GARNISH |
Engage the 2 guides and 23 claws to install the radiator grille garnish.

![]() |
Install the 2 screws.
| 11. INSTALL FRONT BUMPER HOLE COVER |
![]() |
Engage the hook.
| *a | Hook |
Engage the guide and 2 claws to install the front bumper hole cover.
| 12. INSTALL NO. 2 RADIATOR GRILLE MOULDING |
![]() |
Engage the hook.
| *a | Hook |
Engage the 2 claws to install the No. 2 radiator grille moulding.
| 13. INSTALL LOWER NO. 1 RADIATOR GRILLE |
Engage the 13 claws to install the lower No. 1 radiator grille.

| 14. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM |
![]() |
Engage the 2 guides and 4 claws to install the radiator grille (or front panel) emblem.
Install the 2 screws.
| 15. INSTALL RADIATOR GRILLE |
![]() |
Engage the 11 claws to install the radiator grille.
| 16. INSTALL UPPER FRONT BUMPER RETAINER |
![]() |
Install the upper front bumper retainer with the 4 clips.
| 17. INSTALL HOOD TO FRONT END PANEL SEAL |
Clean the front bumper cover.
Remove any remaining double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new hood to front end panel seal.
![]() |
Install the hood to front end panel seal as shown in the illustration.
| *a | Double-sided Tape |
Install the 3 clips.
| 18. INSTALL FOG LIGHT COVER LH |
![]() |
Engage the 4 claws to install the fog light cover LH.
| 19. INSTALL FOG LIGHT COVER RH |
| 20. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light) |
Engage the 2 guides to temporarily install the fog light assembly.
Install the fog light assembly with the screw.
| 21. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light) |
| 22. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH |
Install the front turn signal light assembly with the 3 screws.
| 23. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH |
| 24. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET |
![]() |
Engage the 2 claws.
Install the front bumper extension mounting bracket with the 2 screws.