FRONT DOOR > REASSEMBLY |
| 1. PRECAUTION |
| 2. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.

| *A | Pressing Forward | *B | Pulling |
| *1 | Non-padded Side | *2 | Padded Side |
| *3 | Squeegee | *4 | Black Out Tape |
| *5 | Release Paper | - | - |
| *a | Side View | - | - |
| Area | Measurement |
| A | 10 to 20 mm (0.393 to 0.787 in.) |
| B | 30 to 70 mm/sec. (1.18 to 2.76 in./sec.) |
| C | 40 to 50° (for pressing forward) |
| D | 30 to 45° (for pulling) |
Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
| *1 | Squeegee |
| *2 | Hem |
| *a | First |
| *b | Second |
| *c | Third |
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 3. INSTALL NO. 1 BLACK OUT TAPE |
![]() |
Remove the portion of the new No. 1 black out tape at the perforation as shown in the illustration.
| *A | LH Side |
| *B | RH Side |
| *a | Perforation |
| *b | Remove |
| *c | Square |
| *d | Round |
Apply the new No. 1 black out tape to the positions shown in the illustration.

| *1 | Edge of curved surface | - | - |
| Dimension | Measurement |
| a | - 1.0 to 1.0 mm (- 0.0394 to 0.0394 in.) |
| b | 2.0 mm (0.0787 in.) |
| c | 1.0 mm (0.0394 in.) |
| d | 3.0 mm (0.118 in.) |
| e | 3.0 mm (0.118 in.) |
| 4. INSTALL FRONT DOOR PANEL CUSHION |
![]() |
Engage each claw to Install the 2 cushions onto the door panel.
| 5. INSTALL FRONT DOOR LOCK OPEN ROD |
![]() |
Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
| 6. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
![]() |
Engage the guide and 2 clamps.
Temporary install the front door outside handle frame sub-assembly to the front door.
![]() |
Engage the door handle nut and 2 claws.
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.
| 7. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the front door inside locking cable assembly as shown in the illustration.
![]() |
Engage the 3 claws as shown in the illustration.
| 8. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the front door lock remote control cable assembly as shown in the illustration.
| 9. INSTALL FRONT DOOR LOCK ASSEMBLY |
Apply MP grease to the sliding parts of the front door lock assembly.
When reusing the front door lock assembly:
![]() |
Install a new door lock wiring harness seal to the front door lock assembly.
![]() |
Insert the front door lock open rod to the front door lock assembly.
| *1 | Front Door Lock Open Rod |
Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.
Connect the connector.
| 10. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Engage the 2 claws to install the front door outside handle rear pad.
| 11. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Engage the 3 claws to install the front door outside handle front pad.
| 12. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Insert the front end of the front door outside handle assembly into the front door outside handle frame.
Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.
![]() |
Connect the connector.
Engage the 3 claws.
| 13. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side) |
![]() |
Engage the 2 guides and claw to install the front door outside handle cover to the front door lock cylinder.
| 14. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side) |
![]() |
Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
![]() |
Install the hole plug.
| 15. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Install the front door outside handle cover with lock cylinder assembly.
Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.
![]() |
Install the hole plug.
| 16. INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP |
Install the front door fix window glass onto the front door fix window weatherstrip.
![]() |
Install the front door fix window weatherstrip with the front door fix window glass.
| 17. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY |
![]() |
Temporary install the front door front lower frame sub-assembly with the 2 bolts.
Install the screw.
Tighten the 2 bolts to install the front door front lower frame sub-assembly.
| 18. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Engage the guide.
Install the front door rear lower frame sub-assembly with the bolt.
| 19. INSTALL FRONT DOOR WEATHERSTRIP |
![]() |
Engage the 30 clips to install the front door weatherstrip.
| 20. INSTALL FRONT DOOR CHECK ASSEMBLY |
Apply MP grease to the sliding areas of the front door check assembly.
![]() |
Apply adhesive to the threads of the bolt (A).
Install the front door check assembly with the 3 bolts.
| 21. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 22. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
| 23. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the temporary bolt to the front door window regulator assembly.
![]() |
Temporarily install the front door window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 5 bolts.
Connect the connector.
| 24. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the front door No. 2 service hole cover.
| 25. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply new butyl tape to the front door panel.
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
![]() |
Attach the front door service hole cover according to the reference points on the front door panel.
| *a | Reference Point |
| 26. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
Using an air riveter or a hand riveter, install the front No. 1 speaker assembly with 3 new rivets.

| *1 | Riveter | *2 | Mandrel |
| *a | INCORRECT | *b | CORRECT |
Connect the connector.
| 27. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
Install the front No. 2 speaker assembly with the 2 screws.
Connect the connector.
| 28. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER |
Engage the claw to install the outer rear view mirror assembly with cover with the 3 screws.
Connect the connector.
| 29. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP |
![]() |
Engage the 8 claws to install the front door glass inner weatherstrip as shown in the illustration.
| 30. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Engage the 4 guides to install the front door inside handle sub-assembly.
| 31. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
![]() |
Engage the 8 clips.
![]() |
Install the front door trim board sub-assembly with the 3 screws.
![]() |
Engage the claw and close the cover.
| 32. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
Connect the connector.
![]() |
Engage the 4 guides and 10 claws to install power window regulator master switch assembly with front door armrest base panel.
| 33. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect the connector.
![]() |
Engage the 4 guides and 10 claws to install power window regulator switch assembly with front door armrest base panel.
| 34. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 35. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 36. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side) |
| 37. INSPECT POWER WINDOW OPERATION |