Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape elasticity increases.

  1. Before installation

    1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

      NOTICE:
      Do not bend the tape or leave it in high temperature places.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

    NOTICE:
    1. Position the tape accurately to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit any more after being removed.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.


      B200106E02


      Text in Illustration 
      *A
      Pressing Forward
      *B
      Pulling
      *1
      Non-padded Side
      *2
      Padded Side
      *3
      Squeegee
      *4
      Black Out Tape
      *5
      Release Paper
      -
      -
      *a
      Side View
      -
      -
      Reference Measurement 
      Area
      Measurement
      A
      10 to 20 mm (0.393 to 0.787 in.)
      B
      30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
      C
      40 to 50° (for pressing forward)
      D
      30 to 45° (for pulling)

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.

      HINT:
      1. Either angle of the squeegee (pressing forward or pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)



      B147253E09
    1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
      Text in Illustration 
      *1
      Squeegee
      *2
      Hem
      *a
      First
      *b
      Second
      *c
      Third

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

  1. Check after installation

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

      NOTICE:
      Do not reuse the tape.



3. INSTALL NO. 2 BLACK OUT TAPE


    B298008E01
  1. Remove the portion of the new No. 2 black out tape at the perforation as shown in the illustration.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Perforation
    *b
    Remove
    *c
    Triangle



  1. Apply the new No. 2 black out tape to the positions shown in the illustration.


    B298007E01


    Text in Illustration 
    *1
    Edge of curved surface
    -
    -

    Standard Measurement:
    Dimension
    Measurement
    a
    3.0 mm (0.118 in.)
    b
    3.0 mm (0.118 in.)
    c
    2.0 mm (0.0787 in.)
    d
    1.0 mm (0.0394 in.)
    e
    -1.0 to 1.0 mm (-0.0394 to 0.0394 in.)



4. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.



    B307163E02
  1. Engage the door handle nut and claw.
    Text in Illustration 
    *a
    Outside
    *b
    Inside

  1. Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



5. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD


    B307161
  1. Engage the 2 claws and install the rear door outside handle rear pad.



6. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD


    B307160
  1. Engage the 3 claws to install the rear door outside handle front pad.



7. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B307164
  1. Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

    NOTICE:
    If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.

  1. Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.



8. INSTALL REAR DOOR OUTSIDE HANDLE COVER


    B307158
  1. Engage the claw to install the rear door outside handle cover.

  1. Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



9. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307165
  1. Install the rear door inside locking cable assembly as shown in the illustration.



    B307166
  1. Engage the 3 claws as shown in the illustration.



10. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307167
  1. Install the rear door lock remote control cable assembly as shown in the illustration.



    B307168
  1. Engage the claw as shown in the illustration.



11. INSTALL REAR DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.

  1. Apply MP grease to the sliding parts of the rear door lock assembly.



  1. When reusing the rear door lock assembly:



      B307153
    1. Install a new door lock wiring harness seal to the rear door lock assembly.



    B307170E01
  1. Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
    Text in Illustration 
    *1
    Release Plate

    NOTICE:
    Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



    B307151
  1. Install the rear door lock child protection cover.



12. INSTALL REAR DOOR QUARTER WINDOW GLASS
  1. Install the rear door quarter window weatherstrip to the rear door quarter window glass.



    B307171
  1. Install the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.



13. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298002
  1. Engage the guide and 4 claws to install the rear door glass outer weatherstrip assembly.



14. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.



    B307149
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



15. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

  1. Install the temporary bolt to the rear door window regulator assembly.



    B307148E02
  1. Temporarily install the rear door window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



16. INSTALL REAR DOOR GLASS CHANNEL FILLER
  1. Apply soapy water to a new rear door glass channel filler.



    B307172E01
  1. Install the new rear door glass channel filler as shown in the illustration.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side
    *c
    Edge of curved surface
    Area
    Measurement
    A
    5.0 mm (0.197 in.)
    B
    5.0 mm (0.197 in.)



17. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
  1. Apply soapy water to a rear door glass channel.



    B307173E01
  1. Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel sub-assembly.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side
    *c
    Edge of curved surface
    Area
    Measurement
    A
    5.0 mm (0.197 in.)
    B
    5.0 mm (0.197 in.)

    NOTICE:
    1. Be careful not to damage the glass or glass channel.
    2. Make sure the position of the rear door glass channel filler does not change.



18. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B307174E01
  1. Insert the rear door glass as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.

  1. Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.



19. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Temporary install the rear door window division bar sub-assembly with the 2 bolts.

    NOTICE:
    Do not damage the rear door glass.

  1. Install the rear door window division bar sub-assembly with the 2 bolts and screw.



20. INSTALL REAR DOOR GLASS RUN


    B307143
  1. Install the rear door glass run.



21. INSTALL REAR DOOR WEATHERSTRIP
  1. Clean the rear door panel sub-assembly.



    B307142E01
  1. Engage the 30 clips to install a new front door weatherstrip.
    Text in Illustration 
    *1
    Double-sided tape



22. INSTALL REAR DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the rear door check assembly.



    B307141E02
  1. Apply adhesive to the threads of the bolt (A).

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the rear door check assembly with the 3 bolts.

    Torque:
    Bolt (A):
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    Bolt (B):
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



23. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.

  1. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.



    B307175E01
  1. Attach the rear door service hole cover according to the reference points on the rear door panel.
    Text in Illustration 
    *a
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.



24. INSTALL REAR SPEAKER ASSEMBLY


  1. Using an air riveter or a hand riveter, install the rear speaker assembly with 3 new rivets.


    E244889E01


    Text in Illustration 
    *1
    Riveter
    *2
    Mandrel
    *a
    INCORRECT
    *b
    CORRECT

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. Do not pry on the rivets with the riveter, as this will cause damage to the riveter and mandrel.
    3. Confirm that the rivets are seated properly against the speaker.
    4. Do not tilt the riveter when installing the rivets to the speaker.
    5. Do not leave any clearance between the rivet heads and speaker.
    6. Do not leave any clearance between the speaker and door. Firmly hold the 2 items together while installing the rivets.

    HINT:
    1. Install the rivets in the order shown in the illustration.
    2. If the rivet cannot be cut, pull it once and cut it.

  1. Connect the connector.



25. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP


    B307177
  1. Engage the 5 claws to install the rear door glass inner weatherstrip as shown in the illustration.



26. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B307136
  1. Engage the 4 guides to install the rear door inside handle sub-assembly.



27. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307178E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



    B307182
  1. Engage the 7 clips.



    B308235
  1. Engage the clip.



    B307134
  1. Install the rear door trim board sub-assembly with the 3 screws.



    B307179
  1. Engage the claw and close the cover.



28. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
  1. Connect the connector.



    B307129
  1. Engage the 3 guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



29. INSTALL REAR DOOR FRAME GARNISH


    B307128
  1. Engage the guide.

  1. Engage the 2 clips and 3 claws to install the rear door frame garnish.



30. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



31. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



32. INSPECT POWER WINDOW OPERATION
(Click here)