SMART ENTRY AND START SYSTEM (for Entry Function) > OPERATION CHECK |
| CHECK SMART ENTRY AND START SYSTEM (for Entry Function) OPERATION |
Check the entry unlock function (driver door, front passenger door).
Perform a wireless lock operation to lock the door, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.
![]() |
Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly and approximately 0.7 m (2.30 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
With the system in unlock standby mode, grasp the front door outside handle assembly and check that the door unlocks.
![]() |
Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.
| *A | for LHD |
| *B | for RHD |
| *a | Unlock Sensor (Backside) |
![]() |
Check the entry lock function (driver door, front passenger door).
| *A | for LHD |
| *B | for RHD |
| *a | Lock Sensor |
With the door closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.
![]() |
Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly approximately 0.1 m (0.328 ft.) below the bottom edge of the door glass and approximately 0.3 m (0.984 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that the door locks.
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
Check the entry luggage compartment open function.
![]() |
Perform a wireless lock operation to lock the doors, operate the unlock switch of the luggage door opening switch assembly while carrying the electrical key transmitter sub-assembly and check that the door unlocks.
| *1 | Unlock Switch |
| *a | Approximately 0.7 m (2.30 ft.) |
Inspect the entry back door unlock operating range. While standing at the rear of the vehicle, hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the illustration at the same height as the back door opener switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle, press the unlock switch of the back door opener switch assembly and check that the door unlock.
Check the entry back door lock function.
With the door closed and unlocked, press the lock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the door lock.
![]() |
Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the illustration at the same height as the top edge of the rear bumper and approximately 0.3 m (0.984 ft.) from the vehicle, press the lock of the back door opener switch assembly and check that the door lock.
| *1 | Lock Switch |
| *a | Approximately 0.3 m (.0.984 ft.) |
Check the push start function.
With the power switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter sub-assembly. Then, press the power switch and check that the hybrid system starts.
With the brake pedal released and the power switch off, press the power switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.
Stop the vehicle, press the power switch and check that the power source mode changes to off (the hybrid system stops and all electrical systems are off).
![]() |
Inspect the push start operating range (steering column). Place the electrical key transmitter sub-assembly on the steering column at inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.
| *A | for LHD |
| *B | for RHD |
| *a | Inspection Point |
![]() |
Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.
| *a | Inspection Point |
![]() |
Inspect the push start operating range (rear floor). Place the electrical key transmitter sub-assembly on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.
| *a | Inspection Point |
Check the key lock-in prevention function (vehicle interior).
Turn the power switch off.
Place the electrical key transmitter sub-assembly on a front or rear seat.
Close the door, making sure the doors are unlocked.
Touch a door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.
Check the transmitter battery saving function (w/ Tire Pressure Warning System)
Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock button and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
Check that the smart entry and start system (for Entry Function) does not operate while in transmitter battery saving mode.
Check the entry cancel function.
Cancel the smart entry and start system and check that all the functions of the smart entry and start system (for Entry Function) no longer operate.
While the key cancel function (entry cancel function) is on, check that all functions of the smart entry and start system cannot be operated.
Check the answer-back function (hazard warning light flashing and buzzer sounding).
| Entry Operation | Wireless Buzzer* | Hazard Warning Light |
| Entry Door Lock | Sounds once | Flashes once |
| Entry Door Unlock | Sounds twice | Flashes twice |
| Entry Back Door Lock | Sounds once | Flashes once |
| Entry Back Door Unlock | Sounds twice | Flashes twice |
| KEY DIAGNOSTIC MODE (Using Intelligent Tester) |
Enter the following menus: Body / Entry&Start / Utility / Communication Check (Key Diag Mode).
Inspect the appropriate item according to the following table.
| Tester Display | Inspection Item |
| Overhead + Driver Side*1 | Front door outside handle assembly (electrical key antenna) [for Driver Side] |
| Overhead + Passenger Side*2 | Front door outside handle assembly (electrical key antenna) [for Front Passenger Side] |
| Overhead + Front Room*3 | No. 1 indoor electrical key antenna assembly (front floor) |
| Overhead + Rear Room*4 | No. 2 indoor electrical key antenna assembly (steering column) |
| Overhead + Back Door*5 | Electrical key antenna (outside luggage) |
| Luggage + Back Door (inside)*6 | No. 3 indoor electrical key antenna assembly (rear floor) |
| Luggage + Luggage*7 | Electrical key antenna (outside luggage) |
| Immobiliser Amp*8 | Amplifier (power switch) |
| Tester Display | Inspection Item |
| [CH1/CH2] Overhead + Driver Side*1 | Front door outside handle assembly (electrical key antenna) [for Driver Side] |
| [CH1] Overhead + Driver Side*1 | |
| [CH2] Overhead + Driver Side*1 | |
| [CH1/CH2] Overhead + Passenger Side*2 | Front door outside handle assembly (electrical key antenna) [for Front Passenger Side] |
| [CH1] Overhead + Passenger Side*2 | |
| [CH2] Overhead + Passenger Side*2 | |
| [CH1/CH2] Overhead + Front Room*3 | No. 1 indoor electrical key antenna assembly (front floor) |
| [CH1] Overhead + Front Room*3 | |
| [CH2] Overhead + Front Room*3 | |
| [CH1/CH2] Overhead + Rear Room*4 | No. 2 indoor electrical key antenna assembly (steering column) |
| [CH1] Overhead + Rear Room*4 | |
| [CH2] Overhead + Rear Room*4 | |
| [CH1/CH2] Overhead + Back Door*5 | Electrical key antenna (outside luggage) |
| [CH1] Overhead + Back Door*5 | |
| [CH2] Overhead + Back Door*5 | |
| [CH1/CH2] Overhead + Back Door (inside)*6 | No. 3 indoor electrical key antenna assembly (rear floor) |
| [CH1] Overhead + Back Door (inside)*6 | |
| [CH2] Overhead + Back Door (inside)*6 | |
| [CH1/CH2] Immobiliser Amp*7 | Amplifier (power switch) |
| [CH1] Immobiliser Amp*7 | |
| [CH2] Immobiliser Amp*7 |
Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.
![]() |
*1: Front door outside handle assembly (for Driver Side)
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
![]() |
*3: No. 1 indoor electrical key antenna assembly (front floor)
| *a | Inspection Point |
![]() |
*4: No. 2 indoor electrical key antenna assembly (steering column)
| *A | for LHD |
| *B | for RHD |
| *a | Inspection Point |
![]() |
*5, *7: Electrical key antenna (outside luggage)
| *a | Approximately 0.7 m (2.30 ft.) |
![]() |
*6: No. 3 indoor electrical key antenna (rear floor)
| *a | Inspection Point |
![]() |
*8: Amplifier (power switch)
| *A | for Type A |
| *B | for Type B |