Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
  1. Engage the clamp of fuel lid lock control cable sub-assembly.

  1. Engage the fuel lid lock control cable sub-assembly to clamps.



    B297021
  1. Engage the 2 claws to install the fuel lid lock control cable sub-assembly.



2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
  1. Connect the fuel lid lock control cable.



    B307905
  1. Engage the guide.

  1. Install the fuel lid lock open lever sub-assembly with the screw.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


  1. Engage the guide, 4 claws and 4 clips.


    B300800E01


    Text in Illustration 
    *1
    Rear Seatback Hinge
    -
    -

  1. Install the deck trim side panel assembly LH with the bolt and 2 screws.

  1. Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.



4. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
  1. Connect the connector.



    E288706
  1. Engage the claw to install the No. 1 luggage compartment light assembly.



5. INSTALL REAR ABSORBER CAP LH
  1. Engage the 2 guides and 2 claws to install the rear absorber cap LH.



6. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Engage the 2 claws.

  1. Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



7. INSTALL REAR DECK TRIM COVER
  1. Engage the 2 guides and 4 claws.

  1. Install the rear deck trim cover with the 2 clips.



8. INSTALL DECK FLOOR BOX LH
  1. Install the deck floor box LH.



9. INSTALL DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board assembly.



11. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Install the package tray trim panel assembly.



12. INSTALL CENTER PILLAR LOWER GARNISH LH
  1. Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.



13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B299875E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (White)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



14. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the guide and the 5 claws to install the rear door scuff plate.



15. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B299871E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



16. INSTALL COWL SIDE TRIM BOARD LH
  1. Engage the clip.

  1. Install the cowl side trim board with the clip.



17. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 8 claws to install the front door scuff plate.



18. INSTALL REAR SEATBACK ASSEMBLY LH
  1. Place the rear seatback assembly LH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly LH with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Raise the rear seatback assembly LH.



19. INSTALL REAR SEAT CUSHION ASSEMBLY
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B296198
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



20. INSTALL FRONT CENTER FLOOR COVER
  1. Engage the 2 guides to install the front center floor cover.

  1. Install the 3 clips.



21. INSTALL FRONT FLOOR COVER LH
  1. Engage the 3 guides.



    B301490E01
  1. Engage the clip <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



22. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



23. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


24. INSTALL REAR SEAT HEADREST ASSEMBLY


25. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)