DOOR CONTROL RECEIVER > REMOVAL |
| 1. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 2. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY |
| 3. REMOVE FRONT FLOOR COVER RH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover RH.
| 4. REMOVE FRONT FLOOR COVER LH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover LH.
| 5. REMOVE FRONT CENTER FLOOR COVER |
![]() |
Using a clip remover, remove the 3 clips.
Disengage the 2 guides and remove the front center floor cover.
| 6. REMOVE REAR SEATBACK ASSEMBLY (for Bench Type Seatback) |
Fold down the rear seatback assembly.
![]() |
Remove the 2 bolts and rear seatback assembly.
| 7. REMOVE REAR SEATBACK ASSEMBLY LH (for Separate Type Seatback) |
Fold down the rear seatback assembly LH.
![]() |
Remove the 2 bolts and rear seatback assembly LH.
| 8. REMOVE REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback) |
![]() |
Using a clip remover, disengage the 2 clips.
| *a | for RH Side |
| *b | for LH Side |
![]() |
Disengage the 2 rear seat cushion lock hooks of the rear seat cushion assembly from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
![]() |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
| *a | Hook |
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 9. REMOVE REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback) |
![]() |
Disengage the 2 clips.
| *a | RH Side |
| *b | LH Side |
![]() |
Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 10. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 5 claws and guide and remove the rear door scuff plate LH.
| 11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the rear door opening trim weatherstrip LH.
| 12. REMOVE DECK BOARD ASSEMBLY |
Remove the deck board assembly.
| 13. REMOVE DECK FLOOR BOX LH |
Remove the deck floor box LH.
| 14. REMOVE DECK FLOOR BOX RH |
| 15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
Remove the package tray trim panel assembly.
| 16. REMOVE REAR DECK TRIM COVER |
![]() |
Remove the 2 clips.
Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.
| 17. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
Remove the bolt.
![]() |
Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.
| 18. REMOVE REAR ABSORBER CAP LH |
![]() |
Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.
| 19. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *a | Protective Tape |
![]() |
Remove the No. 1 luggage compartment light assembly as shown in the illustration.
Disconnect the connector and remove the No. 1 luggage compartment light assembly.
| 20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.

| *1 | Rear Seatback Hinge | - | - |
Remove the bolt and 2 screws.
Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.
| 21. REMOVE ROOF SIDE INNER GARNISH LH |
Disengage the 5 clips.

Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.
| 22. REMOVE DOOR CONTROL RECEIVER |
![]() |
Disconnect the connector.
Remove the bolt and door control receiver.