Home › Engine / Hybrid System › 1NZ-FXE COOLING › COOLING FAN SYSTEM

COOLING FAN SYSTEM > Cooling Fan Circuit

for Preparation Click here


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, inverter coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM

Refer to System Diagram (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

  1. Check the operation of the cooling fan while operating them using the tester.

    OK:

    Tester Operation
    Specified Condition
    ON
    Cooling fan operating
    OFF
    Cooling fan stopped


    Result:

    Result
    Proceed to
    OK
    A
    NG (Cooling fan does not operate)
    B
    NG (Cooling fan does not stop)
    C



B
Go to step 2

C
Go to step 11
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT COOLING FAN MOTOR
  1. Inspect the cooling fan motor (Click here).



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)


    A266912E03
  1. Disconnect the cooling fan ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A52-1 (+B1) - A52-3 (E1)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Cooling Fan ECU)



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
  1. Disconnect the ECM connector.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A40-45 (RFC) or A52-2 (SI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A52-3 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)
OK


6.INSPECT COOLING FAN RELAY (FAN RELAY)
  1. Inspect the FAN relay (Click here).



NG
REPLACE COOLING FAN RELAY (FAN RELAY)
OK


7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)


    A269760E01
  1. Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (FAN relay) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    FAN Relay



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - AUXILIARY BATTERY)
OK


8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)
  1. Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A52-1 (+B1) - 5 (FAN relay)
    Always
    Below 1 Ω
    A52-1 (+B1) or 5 (FAN relay) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN RELAY)
OK


9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)
  1. Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2 (FAN relay) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BODY GROUND)
OK


10.CHECK HARNESS AND CONNECTOR (FAN RELAY - NO. 1 INTEGRATION RELAY)
  1. Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1(FAN relay) - 2C-4
    Always
    Below 1 Ω
    1(FAN relay) or 2C-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - NO. 1 INTEGRATION RELAY)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
  1. Disconnect the ECM connector.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A40-45 (RFC) - A52-2 (SI)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)
OK


12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)


    A255684E10
  1. Disconnect the cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z4-1 (-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Cooling Fan Motor)



NG
REPLACE COOLING FAN MOTOR (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)