BRAKE BOOSTER (for RHD) > INSTALLATION |
| 1. INSTALL BRAKE BOOSTER GASKET |
Install a new brake booster gasket to the brake booster with master cylinder assembly.
| 2. INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
![]() |
Install the brake booster with master cylinder assembly with the 4 nuts.
| *1 | Connector Portion |
| *2 | Union |
| *3 | Brake Master Cylinder Push Rod Clevis |
| *4 | Boot |
| *5 | Front No. 2 Brake Tube |
Install the wire harness clamp to the stud bolt of the brake booster with master cylinder assembly.
![]() |
Connect the connector to the brake booster with master cylinder assembly.
![]() | Connect the connector |
![]() | Lock the lock lever |
| 3. CONNECT BRAKE LINE |
Install the brake tube clamp to the clamp bracket of the brake booster with master cylinder assembly.
![]() |
Temporarily tighten each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.
| *a | to Front Wheel Cylinder LH |
| *b | to Rear Wheel Cylinder RH |
| *c | to Brake Booster Pump Assembly |
| *d | to Rear Wheel Cylinder LH |
| *e | to Front Wheel Cylinder RH |
Using a union nut wrench, fully tighten each brake line.
| 4. INSTALL PUSH ROD PIN |
![]() |
Apply lithium soap base glycol grease to the push rod pin and installation hole of the brake pedal sub-assembly.
![]() | Lithium Soap Base Glycol Grease |
Install the push rod pin and a new clip to connect the push rod clevis to the brake pedal support assembly.
| 5. INSTALL BRAKE PEDAL RETURN SPRING |
Install the brake pedal return spring to the brake pedal support assembly.
| 6. INSTALL RESERVOIR BRACKET |
Install the reservoir bracket with the bolt and nut.
| 7. CONNECT NO. 2 BRAKE ACTUATOR HOSE |
![]() |
Connect the No. 2 brake actuator hose to the No. 1 brake actuator tube with the clip.
![]() | Front of Vehicle |
| 8. CONNECT NO. 1 RESERVOIR HOSE |
![]() |
Connect the No. 1 reservoir hose to the brake booster with master cylinder assembly with the clip.
![]() | Up |
| 9. CONNECT NO. 2 RESERVOIR HOSE |
![]() |
Connect the No. 2 reservoir hose to the brake booster with master cylinder assembly with the clip.
![]() | Up |
| 10. BLEED NO. 1 BRAKE ACTUATOR TUBE |
Add brake fluid into the brake master cylinder reservoir assembly.
![]() |
Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the No. 1 brake actuator tube.
| *1 | No. 1 Brake Actuator Tube |
| 11. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 nuts.
| 12. FILL RESERVOIR WITH BRAKE FLUID |
| 13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 14. BLEED BRAKE SYSTEM |
Remove the outer cowl top panel sub-assembly.
Bleed the brake system.
Wait at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.

| *A | for LHD | *B | for RHD |
Remove the brake master cylinder reservoir filler cap assembly.

| *A | for LHD | *B | for RHD |
Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.
Connect the intelligent tester to the DLC3 and turn the power switch on (IG).
Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.
Select "ABS actuator has been replaced" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.
![]() |
After air bleeding, tighten each bleeder plug.
| *1 | Stroke Simulator Bleeder Plug |
Clear the DTCs (Click here).
Turn the intelligent tester off and turn the power switch off.
Install the brake master cylinder reservoir filler cap.
Inspect for brake fluid leaks.
Install the outer cowl top panel sub-assembly.
| 15. INSPECT AND ADJUST BRAKE PEDAL |
| 16. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR |
| 17. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and nut.
Engage the 3 clamps to install the wire harness.
| 18. INSTALL FRONT NO. 1 VENTILATOR SEAL |
Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.
| 19. INSTALL FRONT AIR SHUTTER SEAL |
Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.
| 20. INSTALL INNER COWL TOP TO COWL BRACE |
![]() |
Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.
| 21. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |