Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
  1. Power window regulator motor assembly (for driver door)
  2. Main body ECU (multiplex network body ECU)
  3. Instrument panel junction block assembly
  4. Wire harness or connector

WIRING DIAGRAM


B274860E22


INSPECTION PROCEDURE

NOTICE:
  1. When the power window regulator motor assembly (for driver door) is replaced or removed and reinstalled, it requires initialization (Click here).
  2. When using the intelligent tester to troubleshoot with the power switch off:
    Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).



  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


    B281983E08

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3B-12 (LIN2) - MB-16 (LIN2)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *b
    Component without harness connected
    (Instrument Panel Junction Block Assembly)

  1. Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

  1. Install the instrument panel junction block assembly (Click here).



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - EACH ECU)
  1. Disconnect the J3*1 or H3*2 power window regulator motor (for driver door) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    3B-12 (LIN2) - J3-9 (LIN)
    Always
    Below 1 Ω
    J3-9 (LIN) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    3B-12 (LIN2) - H3-9 (LIN)
    Always
    Below 1 Ω
    J3-9 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR))
  1. Reconnect the 3B instrument panel junction block assembly connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR) (Click here)