REAR WHEEL ALIGNMENT > INSPECTION |
| 1. PRECAUTION |
![]() |
| *a | Colored identification mark on the bottom of the rear coil spring |
| 2. INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
| Tire Size | Front kPa (kgf/cm2, psi) | Rear kPa (kgf/cm2, psi) |
| 175/65R15 84H | 230 (2.3, 33) | 220 (2.2, 32) |
| 195/50R16 84V | 220 (2.2, 32) | 200 (2.0, 29) |
| 185/60R15 84H | 220 (2.2, 32) | 220 (2.2, 32) |
![]() |
Using a dial indicator, check the runout of the tires.
| 3. MEASURE VEHICLE HEIGHT |
Bounce the vehicle up and down at the corners to stabilize the suspension.
![]() |
Measure the vehicle height.
| Tire Size | Front C - A | Rear D - B |
| 175/65R15 | 92 mm (3.62 in.) | 29 mm (1.14 in.) |
| 185/60R15 | 93 mm (3.66 in.) 79 mm (3.11 in.) *1 69 mm (2.72 in.) *2 | 32 mm (1.26 in.) 14 mm (0.55 in.) *1 4 mm (0.16 in.) *2 |
| 195/50R16 | 93 mm (3.66 in.) | 30 mm (1.18 in.) |
| 4. INSPECT CAMBER |
Install a camber-caster-kingpin gauge.
Inspect the camber.
| Tire Size | Camber Inclination | Right-left Difference |
| 185/60R15 | -0°58' +/- 0°30' (-0.97° +/- 0.50°) -0°55' +/- 0°30' (-0.92° +/- 0.50°) *1 -0°54' +/- 0°30' (-0.90° +/- 0.50°) *2 | 0°30' (0.50°) or less |
| 175/65R15 195/50R16 | -0°57' +/- 0°30' (-0.95° +/- 0.50°) |
| 5. INSPECT TOE-IN |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
![]() |
Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
| *a | Tread Center Mark |
| *b | Dimension B |
![]() | Front of the Vehicle |
Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.
![]() |
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| *a | Dimension A |
![]() | Front of the Vehicle |
| Tire Size | Specified Condition | Right-left Difference |
| 185/60R15 | C + D: 0°21' +/- 15' ( 0.35° +/- 0.25°) C + D: 0°17' +/- 15' ( 0.28° +/- 0.25°) *1 C + D: 0°14' +/- 15' ( 0.23° +/- 0.25°) *2 | 30' (0.50°) or less |
| B - A: 3.9 +/- 3 mm (0.154 +/- 0.118 in.) B - A: 3.2 +/- 3 mm (0.126 +/- 0.118 in.) *1 B - A: 2.8 +/- 3 mm (0.110 +/- 0.118 in.) *2 | 6.0 mm (0.236 in.) or less | |
| 175/65R15 195/50R16 | C + D: 0°20' +/- 15' ( 0.33° +/- 0.25°) | 30' (0.50°) or less |
| B - A: 3.9 +/- 3 mm (0.154 +/- 0.118 in.) | 6.0 mm (0.236 in.) or less |
| 6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 7. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION |