DTC P0A7A-203 Generator Inverter Performance |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A7A | 203 | Malfunction (short circuit) in the generator inverter inside the inverter with converter assembly |
|
| 1.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1) |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect the motor cable from the inverter with converter assembly.
![]() |
Check MG1 for an interphase short using a milliohmmeter.
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a2-1 (W) - a2-2 (U) | Power switch off | 139.1 to 153.7 mΩ |
| a2-2 (U) - a2-3 (V) | Power switch off | 139.1 to 153.7 mΩ |
| a2-3 (V) - a2-1 (W) | Power switch off | 139.1 to 153.7 mΩ |
| *1 | Shield Ground |
| *a | Motor Cable (for MG1) (Inverter with Converter Assembly Side) |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a2-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
Connect the motor cable.
Install the inverter cover.
Install the inverter terminal cover.
|
| ||||
| OK | |
| 2.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS |
| NEXT | |
| 3.CHECK DTC OUTPUT (HYBRID CONTROL) |
Check the other DTCs that were output together with DTC P0A7A-203.
| DTC No. | Relevant Diagnosis |
| P0A7A-122, 322, 324, 325, 517, 518 | Generator Inverter Performance |
| NEXT | ||
| ||
| 4.CHECK MOTOR CABLE (FOR MG1) |
Check that the service plug grip is not installed.
Remove the motor cable (Click here).
![]() |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a2-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a2-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| *1 | Shield ground |
| *a | Motor Cable (for MG1) (Inverter with Converter Assembly Side) |
| *b | Motor Cable (for MG1) (Hybrid Vehicle Transaxle Assembly Side) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a2-1 (W) - a1-1 (W) | Power switch off | Below 1 Ω |
| a2-2 (U) - a1-2 (U) | Power switch off | Below 1 Ω |
| a2-3 (V) - a1-3 (V) | Power switch off | Below 1 Ω |
| a2-1 (W) - a1-2 (U) | Power switch off | 100 MΩ or higher |
| a2-2 (U) - a1-3 (V) | Power switch off | 100 MΩ or higher |
| a2-3 (V) - a1-1 (W) | Power switch off | 100 MΩ or higher |
Install the motor cable.
|
| ||||
| OK | |
| 5.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY |
| NEXT | |
| 6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS |
| NEXT | |
| 7.CHECK DTC OUTPUT (HYBRID CONTROL) |
Check the other DTCs that were output together with DTC P0A7A-203.
| DTC No. | Relevant Diagnosis |
| P0A7A-122, 322, 324, 325, 517, 518 | Generator Inverter Performance |
| NEXT | ||
| ||
| 8.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1) |
Check that the service plug grip is not installed.
Remove the inverter with converter assembly.
Disconnect the motor cable (for MG1) from the hybrid vehicle transaxle assembly.
![]() |
Check MG1 for an interphase short using a milliohmmeter.
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a1-1 (W) - a1-2 (U) | Power switch off | 136.4 to 150.8 mΩ |
| a1-2 (U) - a1-3 (V) | Power switch off | 136.4 to 150.8 mΩ |
| a1-3 (V) - a1-1 (W) | Power switch off | 136.4 to 150.8 mΩ |
| *a | Component without motor cable (for MG1) connected (Hybrid Vehicle Transaxle Assembly) |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a1-1 (W) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a1-2 (U) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
| a1-3 (V) - Body ground and shield ground | Power switch off | 100 MΩ or higher |
Connect the motor cable.
Install the inverter with converter assembly.
|
| ||||
| OK | |
| 9.REPLACE MOTOR CABLE |
| NEXT | |
| 10.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS |
| NEXT | |
| 11.CHECK DTC OUTPUT (HYBRID CONTROL) |
Check the other DTCs that were output together with DTC P0A7A-203.
| DTC No. | Relevant Diagnosis |
| P0A7A-122, 322, 324, 325, 517, 518 | Generator Inverter Performance |
| NEXT | ||
| ||
| 12.REPLACE MOTOR CABLE |
| NEXT | |
| 13.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY |
| NEXT | |
| 14.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS |
| NEXT | |
| 15.CHECK DTC OUTPUT (HYBRID CONTROL) |
Check the other DTCs that were output together with DTC P0A7A-203.
| DTC No. | Relevant Diagnosis |
| P0A7A-122, 322, 324, 325, 517, 518 | Generator Inverter Performance |
| NEXT | ||
| ||