Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > Pattern Select Switch EV Mode Circuit

for Preparation Click here


DESCRIPTION

The EV drive mode signal is sent to the power management control ECU. This signal is then transmitted from the power management control ECU via CAN to the combination meter assembly to illuminate the EV mode indicator light.

WIRING DIAGRAM


A259907E06


INSPECTION PROCEDURE

If any of the following conditions are not met, EV drive mode may not be turned on or the mode may be cancelled. (A buzzer sounds to indicate that the transition to EV drive mode is cancelled.)

EV Drive Mode Entry Condition
Tester Display
Specified Condition
HV battery charge level
State of Charge (All Bat)
Approximately 50% or higher
Accelerator pedal position
Accelerator Degree
Below approximately 30%
Engine coolant temperature
Engine Coolant Temp
0°C (32°F) or higher
HV battery temperature
Temp of Batt TB1 to TB3
Between 10 to 40°C (50 to 104°F)
Vehicle speed
(Varies depending on engine warm-up condition)
Vehicle Spd
Cold: 30 km/h (19 mph) or less
Warmed-up: 45 km/h (28 mph)
Win
Charge Control Value
Below -5000 kW
Wout
Discharge Control Value
11500 kW or higher
Defroster
-
OFF
Cruise control
-
OFF
1.ASK ABOUT VEHICLE CONDITION
  1. Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.

    Result:
    Result
    Proceed to
    No buzzer sounded and no message was displayed on multi-information display.
    A
    A buzzer sounded and a message was displayed on multi-information display.
    B

HINT:
If a buzzer sounds and a message is displayed on multi-information display, one or more of the EV drive mode entry conditions have not been met. Check that all of the EV drive mode entry conditions have been met before pressing the EV drive mode switch (pattern select switch assembly).



B
COMPLETED
A


2.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / CAN Bus Check.

    Result:
    Result
    Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.
    A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
    B

  1. Turn the power switch off.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3.CHECK DTC OUTPUT (ALL CODES)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / Utility / All Codes.

  1. Check DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output.
    A
    DTCs are output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART
A


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. EV MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Body / Combination Meter / Active Test / Indicat. EV Mode.

  1. Perform the "Indicat. EV Mode" Active Test.

    OK:
    The EV mode indicator light comes on or blinks.

  1. Turn the power switch off.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


5.READ VALUE USING INTELLIGENT TESTER (EV REQUEST, EV SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / EV request, EV Switch.

  1. Read the value displayed on the intelligent tester.

    Tester Display
    Measurement Item/Range
    Normal Condition
    EV request
    EV drive mode transition availability/
    ON or OFF
    In EV drive mode: ON
    EV Switch
    EV drive mode switch (pattern select switch assembly) condition/
    ON or OFF
    EV drive mode switch (pattern select switch assembly) being pushed and held: ON

    Result:
    Result
    Proceed to
    The intelligent tester display changes according to the EV drive mode switch (pattern select switch assembly) operation.
    A
    The intelligent tester display does not change according to the EV drive mode switch (pattern select switch assembly) operation.
    B

  1. Turn the power switch off.



B
Go to step 6
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
  1. Remove the EV drive mode switch (pattern select switch assembly) (Click here).



    A259195E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G63-4 (S) - G63-1 (E)
    EV drive mode switch (pattern select switch assembly) being pushed and held
    Below 1 Ω
    EV drive mode switch (pattern select switch assembly) not pushed
    10 kΩ or higher

Text in Illustration 
*a
Component without harness connected
(EV Drive Mode Switch (Pattern Select Switch Assembly))
  1. Install the EV drive mode switch (pattern select switch assembly).



NG
REPLACE EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY) (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY) - BODY GROUND)
  1. Disconnect connector G63 from the EV drive mode switch (pattern select switch assembly).



    A259196E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G63-1 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly))
  1. Connect the EV drive mode switch (pattern select switch assembly) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY))
  1. Disconnect connector G57 from the power management control ECU.

  1. Disconnect connector G63 from the EV drive mode switch (pattern select switch assembly).



    A259932E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G57-13 (EVSW) - G63-4 (S)
    Always
    Below 1 Ω
    G57-13 (EVSW) or G63-4 (S) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Rear view of wire harness connector
(to Power Management Control ECU)
*b
Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly))
  1. Connect the EV drive mode switch (pattern select switch assembly) connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)