DTC B2430 LED Headlight LH Circuit Malfunction |
DTC B2431 LED Headlight RH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2430 | LED headlight LH circuit malfunction |
|
| B2431 | LED headlight RH circuit malfunction |
|

| 1.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| Both DTC B2430 and B2431 are not output. | A |
| Both DTC B2430 and B2431 are output. | B |
| DTC B2430 or B2431 is output. | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT H-LP RELAY |
![]() |
Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage applied between terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY) |
Measure the voltage according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
| Relay terminal 1 - Body ground | Power switch off | 11 to 14 V |
| Relay terminal 5 - Body ground | Power switch off | 11 to 14 V |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH) |
Disconnect the A10 headlight assembly LH connector.
Disconnect the A9 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay terminal 3 - A10-1 (LO) | Always | Below 1 Ω |
| Relay terminal 3 - A9-1 (LO) | Always | Below 1 Ω |
| Relay terminal 3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay terminal 2 - 3C-18 | Always | Below 1 Ω |
| Relay terminal 2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
![]() |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3C-18 - MB-15 (HRLY) | Always | Below 1 Ω |
| 3C-18 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected (Instrument Panel Junction Block Assembly) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY) |
Disconnect the A10 headlight assembly connector or the A9 headlight assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-1 (LO) - Body ground | Power switch off, light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A9-1 (LO) - Body ground | Power switch off, light control switch in head position | 11 to 14 V |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A9-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-3 (LED) - Body ground | Power switch on (IG), light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A9-3 (LED) - Body ground | Power switch on (IG), light control switch in head position | 11 to 14 V |
|
| ||||
| OK | |
| 10.CHECK LIGHT CONTROL ECU |
Replace the headlight control ECU with a new or known good one (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 11.CHECK HEADLIGHT ASSEMBLY |
Replace the headlight assembly with a new or known good one (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY) |
Disconnect the G60 main body ECU (multiplex network body ECU) connector.
Disconnect the A10 headlight assembly connector or the A9 headlight assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G60-24 (LLEW) - A10-3 (LED) | Always | Below 1 Ω |
| G60-24 (LLEW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| G60-21 (RLEW) - A9-3 (LED) | Always | Below 1 Ω |
| G60-21 (RLEW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||