Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING

REAR DOOR BELT MOULDING > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH side.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work (Click here).



2. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE REAR DOOR FRAME GARNISH


    B307128
  1. Disengage the 2 clips and 3 claws.

  1. Disengage the guide and remove the rear door frame garnish.



5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B307129
  1. Disengage the 8 claws and 3 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307133E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B307134
  1. Remove the 3 screws.



    B308235
  1. Disengage the clip.



  1. pull the rear door trim board sub-assembly at the position indicated in the illustration and disengage the 7 clips in the order shown in the illustration.


    B307908

    NOTICE:
    Do not apply excessive force when pulling the rear door trim board sub-assembly.



    B307135E01
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly and remove the rear door trim board.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



7. REMOVE REAR DOOR SERVICE HOLE COVER


    B307139
  1. Remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



8. DISCONNECT REAR DOOR WEATHERSTRIP
  1. Disconnect the upper part of rear door weatherstrip.



9. REMOVE REAR DOOR GLASS RUN


    B307143
  1. Remove the rear door glass run.



10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Remove the 2 bolts and screw, and remove the rear door window division bar sub-assembly.



11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B307145E02
  1. Slide the lower section of the rear door glass and disengage the rear door glass from the rear window regulator sub-assembly.

  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.



12. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298003E01
  1. Apply protective tape to the door panel in the area around the rear door glass outer weatherstrip assembly.
    Text in Illustration 
    *1
    Protective Tape



    B298001E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the guide and remove the rear door glass outer weatherstrip assembly.