Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 1 ROOF WIRE


  1. Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.


    B300775E01


    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Positioning Tape (Red)
    *3
    Positioning Tape
    *4
    Marking

  1. Align the No. 1 roof wire positioning tape with the markings of the roof headlining.

  1. Install the No. 1 roof wire onto the roof headlining with the adhesive tape.

    NOTICE:
    1. Apply the tape securely in place.
    2. Do not touch the adhesive surface when applying the tape to prevent adhesion failure.



2. INSTALL ROOF HEADLINING END PAD
  1. Remove the release paper from a new roof headlining end pad.

    HINT:
    After removing the release paper, keep the exposed adhesive free from foreign matter.



    B301172E01
  1. Align the markings on the roof headlining with the 2 roof headlining end pads and install the pads as shown in the illustration.
    Text in Illustration 
    *1
    Marking



3. INSTALL REAR NO. 2 SIDE RAIL SPACER LH


    B308238E01
  1. Align the markings on the roof headlining with a new rear No. 2 side rail spacer LH and install the spacer using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



4. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL NO. 3 ROOF SILENCER PAD


  1. w/ Silencer Pad:



    1. Align the markings on the roof headlining with a new No. 3 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.


      B297748E01


      Text in Illustration 
      *1
      Hot-melt Glue
      *2
      Marking

      Standard Measurement:
      Dimension
      Measurement
      A
      20 mm (0.787 in.)



6. INSTALL NO. 2 ROOF SILENCER PAD


  1. w/ Silencer Pad:



    1. Align the markings on the roof headlining with a new No. 2 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.


      B297746E01


      Text in Illustration 
      *1
      Hot-melt Glue
      *2
      Marking

      Standard Measurement:
      Dimension
      Measurement
      A
      20 mm (0.787 in.)



7. INSTALL NO. 1 ROOF SILENCER PAD


    B297744E01
  1. Align the markings on the roof headlining with a new No. 1 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Marking

    Standard Measurement:
    Dimension
    Measurement
    A
    20 mm (0.787 in.)



8. INSTALL FRONT ROOF SILENCER PAD


    B297742E01
  1. Align the markings on the roof headlining with a new 2 roof headlining silencer pads and install the pads using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Marking

    Standard Measurement:
    Dimension
    Measurement
    A
    20 mm (0.787 in.)



9. INSTALL UPPER SHOULDER BELT ANCHOR COVER


    B297740
  1. Install the rear seat shoulder belt cover RH to the roof headlining.

  1. Engage the 4 claws to install the seat belt anchor cover.



10. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY


  1. Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the vehicle.


    E237101E01


    Text in Illustration 
    *1
    Tape
    *2
    Marking Tape
    *3
    Protrusion A
    *4
    Edge
    *a
    Front
    -
    -

    HINT:
    Align the taped part of the antenna cable with the protrusion of the roof headlining, and apply tape to secure the cable to the headlining.

  1. Put the pieces of tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

    HINT:
    1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
    2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion A of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them. (1)
    3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape. (2)
    4. If the entire length of the antenna cord does not fit, adjust the length by tucking in the cord at the area shown in the illustration. (3)



11. INSTALL AMPLIFIER MICROPHONE ASSEMBLY
  1. Engage the 2 claws and install the amplifier microphone assembly to roof headlining holder cover.



12. INSTALL ROOF HEADLINING RETAINER COVER
  1. Engage the 4 claws and install the roof headlining retainer cover.

  1. Connect the connector.