ROOF HEADLINING > REMOVAL |
| 1. REMOVE FRONT FLOOR COVER RH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover RH.
| 2. REMOVE FRONT FLOOR COVER LH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover LH.
| 3. REMOVE FRONT CENTER FLOOR COVER |
![]() |
Using a clip remover, remove the 3 clips.
Disengage the 2 guides and remove the front center floor cover.
| 4. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 5. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY |
| 6. REMOVE REAR SEATBACK ASSEMBLY RH |
Fold down the rear seatback assembly RH.
![]() |
Remove the 2 bolts and rear seatback assembly RH.
| 7. REMOVE REAR SEATBACK ASSEMBLY LH |
Fold down the rear seatback assembly LH.
![]() |
Remove the 2 bolts and rear seatback assembly LH.
| 8. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Disengage the 2 clips.
| *a | RH Side |
| *b | LH Side |
![]() |
Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 9. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 5 claws and guide and remove the rear door scuff plate LH.
| 10. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 8 claws and remove the front door scuff plate LH.
| 11. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the clip.
Disengage the clip and remove the cowl side trim board LH.
| 12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the front door opening trim weatherstrip LH.
| 13. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
| *1 | Front Pillar Garnish Clip |
![]() |
Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip 90° in the direction indicated by the arrow (1) shown in the illustration.
| *a | 90° |
| *b | Protective Tape |
Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip.
Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.
![]() |
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
| 14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the rear door opening trim weatherstrip LH.
| 15. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) |
![]() |
Disengage the 3 claws and remove the lap belt outer anchor cover.
| 16. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.
| 17. REMOVE CENTER PILLAR LOWER GARNISH LH |
![]() |
Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.
| 18. REMOVE CENTER PILLAR UPPER GARNISH LH |
![]() |
Remove the 2 screws and disengage the clip.
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
| 19. REMOVE REAR DOOR SCUFF PLATE RH |
| 20. REMOVE FRONT DOOR SCUFF PLATE RH |
| 21. REMOVE COWL SIDE TRIM BOARD RH |
| 22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 23. REMOVE FRONT PILLAR GARNISH RH |
| 24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 25. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) |
| 26. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 27. REMOVE CENTER PILLAR LOWER GARNISH RH |
| 28. REMOVE CENTER PILLAR UPPER GARNISH RH |
| 29. REMOVE DECK BOARD ASSEMBLY |
Remove the deck board assembly.
| 30. REMOVE DECK FLOOR BOX LH |
Remove the deck floor box LH.
| 31. REMOVE DECK FLOOR BOX RH |
| 32. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
Remove the package tray trim panel assembly.
| 33. REMOVE REAR DECK TRIM COVER |
![]() |
Remove the 2 clips.
Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.
| 34. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
Remove the bolt.
![]() |
Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.
| 35. REMOVE REAR ABSORBER CAP LH |
![]() |
Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.
| 36. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *1 | Protective Tape |
Disconnect the connector and remove the No. 1 luggage compartment light assembly.
| 37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.

| *1 | Rear Seatback Hinge | - | - |
Remove the bolt and 2 screws.
Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.
| 38. REMOVE ROOF SIDE INNER GARNISH LH |
Disengage the 5 clips.

Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.
| 39. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH |
| 40. REMOVE REAR ABSORBER CAP RH |
| 41. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
| 42. DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY |
![]() |
Using a moulding remover, disengage the 2 claws and open the cover.
![]() |
Loosen the bolt and disconnect the shoulder anchor of the rear center seat lap type belt assembly.
| 43. REMOVE ROOF SIDE INNER GARNISH RH |
![]() |
Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.
Disengage the 5 clips.

Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.
| 44. REMOVE MAP LIGHT ASSEMBLY |
![]() |
Using a moulding remover, disengage the 4 claws.
| *a | Contact Portion |
Disconnect the connector and remove the map light assembly.
| 45. REMOVE ASSIST GRIP ASSEMBLY |
![]() |
Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.
![]() |
Disengage the 2 clips and remove the assist grip.
| 46. REMOVE VISOR ASSEMBLY LH |
![]() |
Disconnect the visor shaft from the visor holder.
Remove the 2 screws and the visor assembly LH.
| 47. REMOVE VISOR ASSEMBLY RH |
| 48. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.
| 49. REMOVE ROOF HEADLINING ASSEMBLY |

| *A | 1 Claw Type | - | - |
| *a | Front Pillar RH Side | *b | Front Pillar LH Side |
| *c | Rear Pillar RH Side | - | - |

| *A | 2 Claws Type | - | - |
| *a | Front Pillar RH Side | *b | Front Pillar LH Side |
| *c | Rear Pillar RH Side | - | - |
for front pillar RH side:
Disconnect the connector.
Using a clip remover, disengage the 3 clamps.
for front pillar LH side:
Disconnect the connector.
Using a clip remover, disengage the 3 clamps.
for rear pillar RH side:
Disconnect the connector.
Remove the bolt and disconnect the connector bracket.
Using a clip remover, disengage the 2 clamps.
Using a clip remover, remove the 3 clips.
Disengage the claw. (for 1 Claw Type)
Disengage the 2 claws. (for 2 Claws Type)
![]() |
Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.