Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



2. REMOVE FRONT FLOOR COVER LH


    B301490E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301491
  1. Disengage the 3 guides and remove the front floor cover LH.



3. REMOVE FRONT CENTER FLOOR COVER


    B296737
  1. Using a clip remover, remove the 3 clips.

  1. Disengage the 2 guides and remove the front center floor cover.



4. REMOVE REAR SEAT HEADREST ASSEMBLY


5. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY


6. REMOVE REAR SEATBACK ASSEMBLY RH
  1. Fold down the rear seatback assembly RH.



    B296151
  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SEATBACK ASSEMBLY LH
  1. Fold down the rear seatback assembly LH.



    B296146
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



8. REMOVE REAR SEAT CUSHION ASSEMBLY


    B297552E01
  1. Disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



9. REMOVE REAR DOOR SCUFF PLATE LH


    B300785
  1. Disengage the 5 claws and guide and remove the rear door scuff plate LH.



10. REMOVE FRONT DOOR SCUFF PLATE LH


    B300786
  1. Disengage the 8 claws and remove the front door scuff plate LH.



11. REMOVE COWL SIDE TRIM BOARD LH


    B300787
  1. Remove the clip.

  1. Disengage the clip and remove the cowl side trim board LH.



12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip LH.



13. REMOVE FRONT PILLAR GARNISH LH


    E276150E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Let the front pillar garnish LH hang down from the front pillar garnish clip.



    E276147E01
  1. Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip 90° in the direction indicated by the arrow (1) shown in the illustration.
    Text in Illustration 
    *a
    90°
    *b
    Protective Tape

  1. Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip.

    NOTICE:
    1. If the front pillar garnish clip is not removed from the vehicle body and is not damaged, the front pillar garnish clip can be reused.
    2. If the front pillar garnish clip is removed from the vehicle body, make sure to replace it with a new one.

  1. Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.



    B300790E01
  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly

    1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



15. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B307770
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



16. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B307771
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



17. REMOVE CENTER PILLAR LOWER GARNISH LH


    B300794
  1. Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.



18. REMOVE CENTER PILLAR UPPER GARNISH LH


    B300793
  1. Remove the 2 screws and disengage the clip.

  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.



19. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



20. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



21. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure as for the LH side.



22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



23. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



25. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



26. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



27. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



28. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:
Use the same procedure as for the LH side.



29. REMOVE DECK BOARD ASSEMBLY
  1. Remove the deck board assembly.



30. REMOVE DECK FLOOR BOX LH
  1. Remove the deck floor box LH.



31. REMOVE DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



32. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Remove the package tray trim panel assembly.



33. REMOVE REAR DECK TRIM COVER


    B297727
  1. Remove the 2 clips.

  1. Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.



34. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Remove the bolt.



    B307773
  1. Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.



35. REMOVE REAR ABSORBER CAP LH


    B300796
  1. Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.



36. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY


    E286958E03
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *a
    Protective Tape



    E286959
  1. Remove the No. 1 luggage compartment light assembly as shown in the illustration.

  1. Disconnect the connector and remove the No. 1 luggage compartment light assembly.



37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


  1. Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.


    B300799E01


    Text in Illustration 
    *1
    Rear Seatback Hinge
    -
    -

  1. Remove the bolt and 2 screws.

  1. Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.



38. REMOVE ROOF SIDE INNER GARNISH LH


  1. Disengage the 5 clips.


    B299307

  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.



39. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



40. REMOVE REAR ABSORBER CAP RH

HINT:
Use the same procedure as for the LH side.



41. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



42. DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY


    B300537
  1. Using a moulding remover, disengage the 2 claws and open the cover.



    B297186
  1. Loosen the bolt and disconnect the shoulder anchor of the rear center seat lap type belt assembly.



43. REMOVE ROOF SIDE INNER GARNISH RH


    B299306
  1. Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.



  1. Disengage the 5 clips.


    B297735

  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.



44. REMOVE MAP LIGHT ASSEMBLY


    E236388E01
  1. Using a moulding remover, disengage the 4 claws.
    Text in Illustration 
    *a
    Contact Portion

    NOTICE:
    Do not touch the metal plates, especially the contact portions, as it may cause a malfunction such as the light does not illuminate.

  1. Disconnect the connector and remove the map light assembly.



45. REMOVE ASSIST GRIP ASSEMBLY

HINT:
Use the same procedure to remove all assist grips.



    B175478
  1. Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.



    B175479
  1. Disengage the 2 clips and remove the assist grip.



46. REMOVE VISOR ASSEMBLY LH


    B300801
  1. Disconnect the visor shaft from the visor holder.

  1. Remove the 2 screws and the visor assembly LH.



47. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



48. REMOVE VISOR HOLDER


    B151362E04
  1. Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.

    HINT:
    Use the same procedure for the LH side and RH side.



49. REMOVE ROOF HEADLINING ASSEMBLY



B297737E04


Text in Illustration 
*A
1 Claw Type
-
-
*a
Front Pillar RH Side
*b
Front Pillar LH Side
*c
Rear Pillar RH Side
-
-


B335594E03


Text in Illustration 
*A
2 Claws Type
-
-
*a
Front Pillar RH Side
*b
Front Pillar LH Side
*c
Rear Pillar RH Side
-
-
  1. for front pillar RH side:

    1. Disconnect the connector.

    2. Using a clip remover, disengage the 3 clamps.

  1. for front pillar LH side:

    1. Disconnect the connector.

    2. Using a clip remover, disengage the 3 clamps.

  1. for rear pillar RH side:

    1. Disconnect the connector.

    2. Remove the bolt and disconnect the connector bracket.

    3. Using a clip remover, disengage the 2 clamps.

  1. Using a clip remover, remove the 3 clips.

  1. Disengage the claw. (for 1 Claw Type)

  1. Disengage the 2 claws. (for 2 Claws Type)



    B301724
  1. Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.