Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > Pattern Select Switch Eco Mode Circuit

for Preparation Click here


DESCRIPTION

When selecting ECO drive mode, the ECO mode switch (eco switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO drive mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM


A254642E09


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / CAN Bus Check.

    Result:
    Result
    Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.
    A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
    B

  1. Turn the power switch off.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (ALL CODES)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / Utility / All Codes.

  1. Check DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output.
    A
    DTCs are output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART
A


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. ECO MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body / Combination Meter / Active Test / Indicat. ECO Mode.

  1. Perform the "Indicat. ECO MODE" Active Test.

    OK:
    The ECO mode indicator light comes on or blinks.

  1. Turn the power switch off.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.READ VALUE USING INTELLIGENT TESTER (ECO MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Mode.

  1. Read the value displayed on the intelligent tester.

    Tester Display
    Measurement Item/Range
    Normal Condition
    ECO Mode
    ECO drive mode transition availability/
    ON or OFF
    In ECO drive mode: ON

    Result:
    Result
    Proceed to
    The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation.
    A
    The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation.
    B



B
Go to step 5
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body / Air Conditioning / Data List / ECO Switch.

  1. Read the value displayed on the intelligent tester.

    Tester Display
    Measurement Item/Range
    Normal Condition
    ECO Switch
    ECO mode switch (eco switch assembly) condition/
    ON or OFF
    ECO mode switch (eco switch assembly) being pushed and held: ON
    ECO mode switch (eco switch assembly) not pushed: OFF

    Result:
    Result
    Proceed to
    The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation.
    A
    The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation.
    B



B
Go to step 6
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

6.INSPECT ECO MODE SWITCH (ECO SWITCH ASSEMBLY)
  1. Remove the ECO mode switch (eco switch assembly) (Click here).



    A259197E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G62-9 (ECU) - G62-6 (E)
    ECO mode switch (eco switch assembly) being pushed and held
    Below 1 Ω
    ECO mode switch (eco switch assembly) not pushed
    10 kΩ or higher

Text in Illustration 
*a
Component without harness connected
(ECO Mode Switch (Eco Switch Assembly))
  1. Install the ECO mode switch (eco switch assembly).



NG
REPLACE ECO MODE SWITCH (ECO SWITCH ASSEMBLY) (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (ECO SWITCH ASSEMBLY) - BODY GROUND)
  1. Disconnect connector G62 from the ECO mode switch (eco switch assembly).



    A259198E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G62-6 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly))
  1. Connect the ECO mode switch (eco switch assembly) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (ECO SWITCH ASSEMBLY))
  1. Disconnect connector G34 from the air conditioning amplifier assembly.

  1. Disconnect connector G62 from the ECO mode switch (eco switch assembly).



    A259933E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G34-4 (ECOS) - G62-9 (ECU)
    Always
    Below 1 Ω
    G34-4 (ECOS) or G62-9 (ECU) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b
Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly))
  1. Connect the ECO mode switch (eco switch assembly) connector.

  1. Connect the air conditioning amplifier assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)