HYBRID CONTROL SYSTEM > Pattern Select Switch Eco Mode Circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / CAN Bus Check.
| Result | Proceed to |
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. | B |
Turn the power switch off.
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (ALL CODES) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / Utility / All Codes.
Check DTCs.
| Result | Proceed to |
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the power switch off.
|
| ||||
| A | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. ECO MODE) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / Combination Meter / Active Test / Indicat. ECO Mode.
Perform the "Indicat. ECO MODE" Active Test.
Turn the power switch off.
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (ECO MODE) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Mode.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition |
| ECO Mode | ECO drive mode transition availability/ ON or OFF | In ECO drive mode: ON |
| Result | Proceed to |
| The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation. | A |
| The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation. | B |
|
| ||||
| A | ||
| ||
| 5.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / Air Conditioning / Data List / ECO Switch.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition |
| ECO Switch | ECO mode switch (eco switch assembly) condition/ ON or OFF | ECO mode switch (eco switch assembly) being pushed and held: ON ECO mode switch (eco switch assembly) not pushed: OFF |
| Result | Proceed to |
| The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation. | A |
| The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation. | B |
|
| ||||
| A | ||
| ||
| 6.INSPECT ECO MODE SWITCH (ECO SWITCH ASSEMBLY) |
Remove the ECO mode switch (eco switch assembly) (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G62-9 (ECU) - G62-6 (E) | ECO mode switch (eco switch assembly) being pushed and held | Below 1 Ω |
| ECO mode switch (eco switch assembly) not pushed | 10 kΩ or higher |
| *a | Component without harness connected (ECO Mode Switch (Eco Switch Assembly)) |
Install the ECO mode switch (eco switch assembly).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (ECO SWITCH ASSEMBLY) - BODY GROUND) |
Disconnect connector G62 from the ECO mode switch (eco switch assembly).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G62-6 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to ECO Mode Switch (Eco Switch Assembly)) |
Connect the ECO mode switch (eco switch assembly) connector.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (ECO SWITCH ASSEMBLY)) |
Disconnect connector G34 from the air conditioning amplifier assembly.
Disconnect connector G62 from the ECO mode switch (eco switch assembly).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G34-4 (ECOS) - G62-9 (ECU) | Always | Below 1 Ω |
| G34-4 (ECOS) or G62-9 (ECU) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
| *b | Front view of wire harness connector (to ECO Mode Switch (Eco Switch Assembly)) |
Connect the ECO mode switch (eco switch assembly) connector.
Connect the air conditioning amplifier assembly connector.
|
| ||||
| OK | ||
| ||