REAR CENTER SEAT OUTER BELT ASSEMBLY > INSTALLATION |
| 1. INSPECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY |
![]() |
Before installing the rear seat lap type center belt assembly, check the ELR function.
When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
| *1 | Retractor |
| *a | Unlocked |
| *b | Locked |
| *c | 45° |
| 2. INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY |
Engage the 2 guides and temporarily install the rear center seat lap type belt assembly with the bolt.
![]() |
Turn the rear center seat lap type belt assembly clockwise approximately 90° to install the guide.
Install the bolt.
| 3. INSTALL ROOF SIDE INNER GARNISH RH |
Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH.
Engage the 5 clips to install the roof side inner garnish RH.
![]() |
Engage the guide and 4 claws to connect the belt guide.
| 4. CONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY |
Install the shoulder anchor of the rear center seat lap type belt assembly with the bolt.
![]() |
Engage the 2 claws to close the cover as shown in the illustration.
| 5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
| 6. INSTALL REAR ABSORBER CAP RH |
| 7. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH |
| 8. INSTALL REAR DECK TRIM COVER |
Engage the 2 guides and 4 claws.
Install the rear deck trim cover with the 2 clips.
| 9. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
Install the package tray trim panel assembly.
| 10. INSTALL DECK FLOOR BOX LH |
Install the deck floor box LH.
| 11. INSTALL DECK FLOOR BOX RH |
| 12. INSTALL DECK BOARD ASSEMBLY |
Install the deck board assembly.
| 13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (Red) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *a | Alignment Mark (Red) |
| *b | Flange Position |
| 14. INSTALL REAR DOOR SCUFF PLATE RH |
| 15. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback) |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 16. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback) |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
| *a | Hook |
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 17. INSTALL REAR SEATBACK ASSEMBLY RH (for Separate Type Seatback) |
Place the rear seatback assembly RH in the cabin.
Install the rear seatback assembly RH with the 2 bolts.
Raise the rear seatback assembly RH.
| 18. INSTALL REAR SEATBACK ASSEMBLY (for Bench Type Seatback) |
Place the rear seatback assembly in the cabin.
Install the rear seatback assembly with the 2 bolts.
Raise the rear seatback assembly.
| 19. INSTALL FRONT CENTER FLOOR COVER |
Engage the 2 guides to install the front center floor cover.
Install the 3 clips.
| 20. INSTALL FRONT FLOOR COVER LH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover LH.
Install the 2 clips <A>.
| 21. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 22. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 23. INSTALL REAR SEAT HEADREST ASSEMBLY |