Home › Vehicle Interior › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY

REAR CENTER SEAT OUTER BELT ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR SEAT HEADREST ASSEMBLY


2. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY


3. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



4. REMOVE FRONT FLOOR COVER LH


    B301490E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301491
  1. Disengage the 3 guides and remove the front floor cover LH.



5. REMOVE FRONT CENTER FLOOR COVER


    B296737
  1. Using a clip remover, remove the 3 clips.

  1. Disengage the 2 guides and remove the front center floor cover.



6. REMOVE REAR SEATBACK ASSEMBLY RH (for Separate Type Seatback)
  1. Fold down the rear seatback assembly RH.



    B296151
  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SEATBACK ASSEMBLY (for Bench Type Seatback)
  1. Fold down the rear seatback assembly.



    B296118
  1. Remove the 2 bolts and rear seatback assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



8. REMOVE REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)


    B297552E01
  1. Disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



9. REMOVE REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)


    B297552E01
  1. Using a clip remover, disengage the 2 clips.
    Text in Illustration 
    *a
    for RH Side
    *b
    for LH Side



    B296114E01
  1. Disengage the 2 rear seat cushion lock hooks of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.




      B392248E01
    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
      Text in Illustration 
      *a
      Hook

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side .



12. REMOVE DECK BOARD ASSEMBLY
  1. Remove the deck board assembly.



13. REMOVE DECK FLOOR BOX LH
  1. Remove the deck floor box LH.



14. REMOVE DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Remove the package tray trim panel assembly.



16. REMOVE REAR DECK TRIM COVER


    B297727
  1. Remove the 2 clips.

  1. Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.



17. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



18. REMOVE REAR ABSORBER CAP RH

HINT:
Use the same procedure as for the LH side .



19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



20. DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY


    B300537
  1. Using a moulding remover, disengage the 2 claws and open the cover.



    B297186
  1. Loosen the bolt and disconnect the shoulder anchor of the rear center seat lap type belt assembly.



21. REMOVE ROOF SIDE INNER GARNISH RH


    B299306
  1. Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.



  1. Disengage the 5 clips.


    B297735

  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.



22. REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY


    B297189
  1. Remove the bolt.



    B297190
  1. Disengage the guide.

  1. Turn the shoulder anchor counterclockwise approximately 90° and pull it out.



    B297188
  1. Remove the bolt.

  1. Disengage the 2 guides and remove the rear center seat lap type belt assembly.