Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0069-273    Manifold Absolute Pressure - Barometric Pressure Correlation

for Preparation Click here


DESCRIPTION

The atmospheric pressure sensor mounted on the MG ECU circuit board detects the atmospheric pressure. This reading is used to perform system control that considers vehicle usage conditions.

A254661E06


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0069
273
Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor (for EGR control) exceeds a specified value. The same condition recurs within 3 hours when driving in EV mode.
  1. Inverter with converter assembly
  2. Manifold absolute pressure sensor
  3. ECM
  4. Wire harness or connector

WIRING DIAGRAM


A259008E17


INSPECTION PROCEDURE

HINT:
After the repair, perform the following procedure to confirm the repair.
  1. If the values of Data List items "Atmosphere Pressure" and "MAP" are almost the same with the engine stopped and the power switch on (IG), the vehicle is normal.

1.CHECK DTC OUTPUT (ENGINE AND ECT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTCs other than those listed in the following table are output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0107
    Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
    P0108
    Manifold Absolute Pressure / Barometric Pressure Circuit High Input

    HINT:
    P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (SFI SYSTEM) (Click here)
A


2.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0069-273 only is output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0A1A-151, 658,
    Generator Control Module
    P0A1B-786
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P1C2A-155
    Generator A/D Converter Circuit
    P1C73-512
    Sensor Standard Voltage "F" Circuit / Open
    P1CA6-156
    Generator Control Module Malfunction
    P1CA7-193
    Drive Motor Control Module Malfunction
    P2228-268
    Barometric Pressure Sensor "A" Circuit Low
    P2229-269
    Barometric Pressure Sensor "A" Circuit High
    P2511-149
    ECM/PCM Power Relay Sensor Circuit Intermittent
    P3133-659
    Communication Error from Generator to Drive Motor "A"
    P3134-661
    Communication Error from Drive Motor "A" to Generator
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0100-211, 530
    Lost Communication with ECM/PCM "A"
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A


3.READ VALUE USING INTELLIGENT TESTER (MAP, ATMOSPHERE PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.



  1. Using the table, read the normal atmospheric pressure value for the applicable altitude.


    A250945

  1. Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.

    Result:

    Result
    Proceed to
    Other than the following.
    A
    Difference between MAP in Data List and normal atmospheric pressure value is 10 kPa or more.
    B
    Difference between Atmosphere Pressure in Data List and normal atmospheric pressure value is 10 kPa or more.
    C

  1. Turn the power switch off.



B
Go to step 7

C
REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)
A


4.READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Move the shift lever to P.

  1. Connect the intelligent tester to the DLC3.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP

  1. Read the MAP value in the Data List with the engine stopped.

  1. While depressing the brake pedal, turn the power switch on (READY).

  1. With the READY indicator light illuminated, fully depress the accelerator pedal.

  1. Read the MAP value in the Data List with the engine running.

  1. Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.

    OK:
    The MAP value changes (pressure decreases when the engine is started).

  1. Turn the power switch off.



NG
Go to step 7
OK


5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
(Click here)

NEXT


6.READ VALUE USING INTELLIGENT TESTER (MAP, ATMOSPHERE PESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.

  1. Compare the Data List item "MAP" with "Atmosphere Pressure".

    Result:

    Result
    Proceed to
    The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more.
    A
    The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa.
    B

  1. Turn the power switch off.



B
COMPLETED
A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)  

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)


    A209150E13
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C15-3 (VC) - C15-2 (E2)
    Power switch on (IG)
    4.75 to 5.25 V
    C15-1 (PIM) - C15-2 (E2)
    Power switch on (IG)
    3.0 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Manifold Absolute Pressure Sensor)



NG
Go to step 11
OK


8.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
(Click here)

NEXT


9.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


10.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0069-273 is not output.
    A
    P0069-273 is output again.
    B

  1. Turn the power switch off.



B
REPLACE ECM (Click here)
A

COMPLETED 

11.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C15-3 (VC) - C10-118 (VCPM)
    Always
    Below 1 Ω
    C15-2 (E2) - C10-119 (EPIM)
    Always
    Below 1 Ω
    C15-1 (PIM) - C10-87 (PIM)
    Always
    Below 1 Ω
    C15-3 (VC) or C10-118 (VCPM) - Body ground
    Always
    10 kΩ or higher
    C15-1 (PIM) or C10-87 (PIM) - Body ground
    Always
    10 kΩ or higher

    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C15-3 (VC) - C9-118 (VCPM)
    Always
    Below 1 Ω
    C15-2 (E2) - C9-119 (EPIM)
    Always
    Below 1 Ω
    C15-1 (PIM) - C9-87 (PIM)
    Always
    Below 1 Ω
    C15-3 (VC) or C9-118 (VCPM) - Body ground
    Always
    10 kΩ or higher
    C15-1 (PIM) or C9-87 (PIM) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)