BRAKE FLUID > REPLACEMENT |
| 1. REPLACE BRAKE FLUID (for Using the intelligent tester) |
Separate the center No. 1 cowl top ventilator louver.
![]() |
for LHD:
Disengage the 4 claws and 6 guides, and separate the center No. 1 cowl top ventilator louver.
![]() |
for RHD:
Disengage the 3 claws and 5 guides, and separate the center No. 1 cowl top ventilator louver.
Replace brake fluid.
Remove the brake master cylinder reservoir filler cap assembly.

| *A | for LHD | *B | for RHD |
Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.
Connect the intelligent tester to the DLC3 and turn the power switch on (IG).
Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.
Select "Usual air bleeding" on the intelligent tester display, and replace the brake fluid following the instructions on the intelligent tester.
After replacing brake fluid, tighten each bleeder plug.
Install the brake master cylinder reservoir filler cap assembly.
Clear the DTCs (Click here).
Turn the intelligent tester off and turn the power switch off.
Inspect for brake fluid leaks.
Install the center No. 1 cowl top ventilator louver.
for LHD:
Engage the 4 claws and 6 guides to install the center No. 1 cowl top ventilator louver.
for RHD:
Engage the 3 claws and 5 guides to install the center No. 1 cowl top ventilator louver.
| 2. REPLACE BRAKE FLUID (for not Using the intelligent tester) |
| The shift lever is moved to any other position from P. |
| The power switch is turned on (READY). |
| The power switch is turned off. |
| The parking brake is released. |
| The vehicle speed is not 0 km/h (0 mph). |
Remove all 4 wheels.
Enable ECB (Electronically Controlled Brake system) Invalid Mode.
Perform the procedure listed below in 1 minute.
![]() |
Check that the brake warning light / yellow is blinking.
| *a | Brake Warning Light / Yellow |
Separate the center No. 1 cowl top ventilator louver.
![]() |
for LHD:
Disengage the 4 claws and 6 guides, and separate the center No. 1 cowl top ventilator louver.
![]() |
for RHD:
Disengage the 3 claws and 5 guides, and separate the center No. 1 cowl top ventilator louver.
Replace the brake fluid.
Remove the brake master cylinder reservoir filler cap assembly.

| *A | for LHD | *B | for RHD |
Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.
Connect a vinyl tube to the bleeder plug of the front disc brake cylinder assembly RH.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2
Repeat *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.
Tighten the bleeder plug completely.
Replace the brake fluid from the front disc brake cylinder assembly LH using the same procedure as for the RH side.
Connect a vinyl tube to the bleeder plug of the rear wheel cylinder assembly LH.
Loosen the bleeder plug while depressing and holding the brake pedal, and replace the brake fluid with the brake booster pump assembly and solenoid operating.*3
Tighten the bleeder plug, then release the brake pedal.*4
Repeat *3 and *4 until all the air in the brake fluid is completely bled out and new brake fluid comes out.
Tighten the bleeder plug completely.
Replace the brake fluid from the rear wheel cylinder assembly RH using the same procedure as for the LH side.
Turn the power switch off.
Inspect for brake fluid leaks.
Adjust the brake fluid level in the reservoir .
Install the brake master cylinder reservoir filler cap.
Install the center No. 1 cowl top ventilator louver.
for LHD:
Engage the 4 claws and 6 guides to install the center No. 1 cowl top ventilator louver.
for RHD:
Engage the 3 claws and 5 guides to install the center No. 1 cowl top ventilator louver.
Install the 4 wheels.