Home › Engine / Hybrid System › 1NZ-FXE EMISSION CONTROL › EGR COOLER

EGR COOLER > REMOVAL

for Preparation Click here



1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


2. REMOVE INNER COWL TOP TO COWL BRACE (for LHD)


    C250011
  1. Remove the 3 bolts and inner cowl top to cowl brace.



3. REMOVE INNER COWL TOP TO COWL BRACE (for RHD)


    C249834
  1. Remove the 3 bolts and inner cowl top to cowl brace.



4. REMOVE FRONT AIR SHUTTER SEAL (for LHD)


    C250012
  1. Disengage the clamp to remove the front air shutter seal.



5. REMOVE FRONT AIR SHUTTER SEAL (for RHD)


    C249836
  1. Disengage the clamp to remove the front air shutter seal.



6. REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)


    C250013
  1. Disengage the clamp to remove the front No. 1 ventilator seal.



7. REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)


    C249835
  1. Disengage the clamp to remove the front No. 1 ventilator seal.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C250014
  1. Disengage the clamp to separate the wire harness from the outer cowl top panel sub-assembly.



    C250015
  1. Remove the 8 bolts, nut and outer cowl top panel sub-assembly.



9. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C256179
  1. Disengage the 3 clamps to separate the wire harness from the outer cowl top panel sub-assembly.



    C249838
  1. Remove the 8 bolts, nut and outer cowl top panel sub-assembly.



10. DRAIN COOLANT (for Engine)

NOTICE:
Do not remove the water filler cap sub-assembly, engine drain cock plug or radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.



  1. Remove the water filler cap sub-assembly and drain the coolant.


    A267952E01


    Text in Illustration 
    *1
    Water Filler Cap Sub-assembly
    *2
    Radiator Drain Cock Plug
    *3
    Engine Drain Cock Plug
    *4
    Water Filler

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A267960
  1. Remove the stop ring.



    A268695E01
  1. Connect the hose to the engine drain cock plug.
    Text in Illustration 
    *1
    Hose

  1. Pull out the engine drain cock plug and drain the coolant.



11. REMOVE NO. 2 EGR PIPE


    A268229
  1. Disconnect the wire harness clamp.

  1. Disengage the clamp and disconnect the No. 2 water by-pass hose.

  1. Remove the 2 bolts and 2 nuts.

  1. Remove the No. 2 EGR pipe and 2 gaskets.



12. REMOVE EGR COOLER ASSEMBLY


    A267673
  1. Disconnect the 2 connectors and wire harness clamp.



    A267672
  1. Remove the bolt and wire harness clamp bracket.



    A268054
  1. Disconnect the clamp, No. 4 water by-pass hose and No. 5 water by-pass hose.



    A268679
  1. Remove the 2 bolts, nut and EGR valve bracket.



    A268236
  1. Remove the 2 bolts, 2 nuts and EGR valve with cooler assembly.

  1. Remove the gasket.



    A268036
  1. Disconnect the No. 1 water by-pass hose.

  1. Remove the 2 bolts, EGR valve assembly and gasket.



    A268035
  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.