Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP (for RHD)

BRAKE BOOSTER PUMP (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY
  1. Engage the clamp to install the frame wire to the brake actuator bracket assembly.



    C249860E01
  1. Install the brake actuator bracket assembly with the 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Tighten the 3 bolts in the order in the illustration.

  1. Engage the 2 clamps to install the frame wire to the brake actuator bracket assembly.



2. INSTALL ENGINE UNDER COVER LH


3. INSTALL FRONT WHEEL LH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



4. INSTALL BRAKE BOOSTER PUMP ASSEMBLY


    C256176E01
  1. Install the brake booster pump assembly to the brake actuator bracket assembly with the 2 brake booster pump bushings, 2 brake actuator case collars and 2 nuts.
    Text in Illustration 
    *1
    Union
    *2
    Connector
    *3
    Stud
    *4
    Brake Booster Pump Collar
    *5
    Brake Booster Pump Bushing
    *6
    Brake Actuator Bracket Cushion

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Do not carry the brake booster pump assembly by the parts shown in bold (*1, *2 and *3) in the illustration.
    2. Do not drop the brake booster pump assembly when carrying it. If the brake booster pump assembly has been dropped, replace it with a new one.
    3. Do not kink or damage the brake lines. If they are damaged, replace them with new ones.
    4. Be careful not to allow any brake fluid to enter the connector.
    5. When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the brake booster pump collar*4 and brake booster pump bushing*5 are installed on the brake booster pump assembly, and 2 brake actuator bracket cushions*6 are installed on the brake actuator bracket assembly.
    6. If installing a new brake booster pump assembly, do not remove the hole plug before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

  1. Connect the 2 connectors to the brake booster pump assembly.



5. INSTALL NO. 1 BRAKE TUBE CLAMP BRACKET
  1. Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. CONNECT FRONT NO. 1 BRAKE TUBE
  1. Temporarily tighten the union nut of the front No. 1 brake tube to the brake booster pump assembly.

  1. Install the front No. 1 brake tube to the No. 1 brake tube clamp bracket with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Using a union nut wrench, fully tighten the front No. 1 brake tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



7. CONNECT BRAKE ACTUATOR HOSE


  1. Connect the brake actuator hose to the brake booster pump assembly with the clip.


    C280516E01


    Text in Illustration 
    *A
    for Type A
    *B
    for Type B
    V100136
    Front of Vehicle
    -
    -

    NOTICE:
    1. Make sure that the identification mark on the brake actuator hose is within 30° of the brake booster pump rib.
    2. Install the clip within the range shown in the illustration.

  1. Connect the 2 connectors to the ECM .



8. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    C249839
  1. Remove the 2 nuts and separate the brake master cylinder reservoir assembly from the reservoir bracket.



9. BLEED NO. 1 BRAKE ACTUATOR TUBE
  1. Add brake fluid into the brake master cylinder reservoir assembly.



    C249861E01
  1. Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the No. 1 brake actuator tube.
    Text in Illustration 
    *1
    No. 1 Brake Actuator Tube

    NOTICE:
    1. Do not damage the hoses or tubes.
    2. Do not spill the brake fluid.
    3. Continue this procedure until only a minor amount of air remains in the brake actuator tube.



10. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
  1. Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



11. FILL RESERVOIR WITH BRAKE FLUID


12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



13. BLEED BRAKE SYSTEM
  1. Remove the outer cowl top panel sub-assembly.

    1. for LHD: Click here
    2. for RHD: Click here



  1. Bleed the brake system.



    1. Wait at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.


      C259395E01


      Text in Illustration 
      *A
      for LHD
      *B
      for RHD

      NOTICE:
      Do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

      HINT:
      This procedure is not required if the reservoir level switch connector has been disconnected.



    2. Remove the brake master cylinder reservoir filler cap assembly.


      C259396E01


      Text in Illustration 
      *A
      for LHD
      *B
      for RHD

    3. Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    4. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    5. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    6. Select "ABS actuator has been replaced" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

      NOTICE:
      Before following the instructions on the intelligent tester to perform linear valve offset calibration, release the parking brake. When calibration is complete, immediately apply the parking brake.



    7. C249825E01
    8. After air bleeding, tighten each bleeder plug.

      Torque:
      front bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      rear bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
      stroke simulator bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      HINT:
      The stroke simulator bleeder plug is positioned as shown in the illustration.

      Text in Illustration 
      *1
      Stroke Simulator Bleeder Plug

    9. Clear the DTCs (Click here).

    10. Turn the intelligent tester off and turn the power switch off.

    11. Install the brake master cylinder reservoir filler cap.

  1. Inspect for brake fluid leaks.

  1. Install the outer cowl top panel sub-assembly.

    1. for LHD: Click here
    2. for RHD: Click here



14. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C249838E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the 3 clamps to install the wire harness.



15. INSTALL FRONT NO. 1 VENTILATOR SEAL
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



16. INSTALL FRONT AIR SHUTTER SEAL
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



17. INSTALL INNER COWL TOP TO COWL BRACE


    C249834E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



18. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY