Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER

NOISE FILTER > INSTALLATION

for Preparation Click here



1. INSTALL RADIO SETTING CONDENSER


    E183101
  1. Engage the claw to install a new terminal cover to the wire harness.

    NOTICE:
    1. Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.
    2. Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.
    3. Do not use excessive force when inserting the wire harness into the terminal cover.
    4. If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.



    E221975
  1. Engage the 3 claws to install the new terminal cover with wire harness to a new condenser.

    NOTICE:
    1. Do not use excessive force when inserting the terminal cover into the condenser.
    2. If the terminal cover has been deformed during installation, replace the terminal, terminal cover and condenser with new ones.

  1. Engage the clamp to temporarily install a new radio setting condenser with wire harness.

  1. Install the new radio setting condenser with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


  1. Engage the guide, 4 claws and 4 clips.


    B300800E02


    Text in Illustration 
    *a
    Rear Seatback Hinge
    -
    -

  1. Install the deck trim side panel assembly LH with the bolt and 2 screws.

  1. Turn the rear seatback hinge as shown in the illustration.



3. INSTALL REAR ABSORBER CAP LH
  1. Engage the 2 guides and 2 claws to install the rear absorber cap LH.



4. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
  1. Connect the connector.



    E288706
  1. Engage the claw to install the No. 1 luggage compartment light assembly.



5. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Engage the 2 claws.

  1. Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



6. INSTALL REAR DECK TRIM COVER
  1. Engage the 2 guides and 4 claws.

  1. Install the rear deck trim cover with the 2 clips.



7. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Install the package tray trim panel assembly.



8. INSTALL DECK FLOOR BOX LH
  1. Install the deck floor box LH.



9. INSTALL DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board assembly.



11. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B299875E01
  1. Align the alignment mark (White) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (White)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



12. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the guide and the 5 claws to install the rear door scuff plate.



13. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B392248E01
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
    Text in Illustration 
    *a
    Hook



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



14. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B296198
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



15. INSTALL REAR SEATBACK ASSEMBLY LH (for Bench Type Seatback)
  1. Place the rear seatback assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Raise the rear seatback assembly.



16. INSTALL REAR SEATBACK ASSEMBLY LH (for Separate Type Seatback)
  1. Place the rear seatback assembly LH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly LH with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Raise the rear seatback assembly LH.



17. INSTALL FRONT CENTER FLOOR COVER
  1. Engage the 2 guides to install the front center floor cover.

  1. Install the 3 clips.



18. INSTALL FRONT FLOOR COVER LH
  1. Engage the 3 guides.



    B301490E01
  1. Engage the clip <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



19. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



20. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


21. INSTALL REAR SEAT HEADREST ASSEMBLY