Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER

NOISE FILTER > REMOVAL

for Preparation Click here



1. REMOVE REAR SEAT HEADREST ASSEMBLY


2. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY


3. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



4. REMOVE FRONT FLOOR COVER LH


    B301490E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301491
  1. Disengage the 3 guides and remove the front floor cover LH.



5. REMOVE FRONT CENTER FLOOR COVER


    B296737
  1. Using a clip remover, remove the 3 clips.

  1. Disengage the 2 guides and remove the front center floor cover.



6. REMOVE REAR SEATBACK ASSEMBLY (for Bench Type Seatback)
  1. Fold down the rear seatback assembly.



    B296118
  1. Remove the 2 bolts and rear seatback assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SEATBACK ASSEMBLY LH (for Separate Type Seatback)
  1. Fold down the rear seatback assembly LH.



    B296146
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



8. REMOVE REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)


    B297552E01
  1. Using a clip remover, disengage the 2 clips.
    Text in Illustration 
    *a
    for RH Side
    *b
    for LH Side



    B296114E01
  1. Disengage the 2 rear seat cushion lock hooks of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.




      B392248E01
    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
      Text in Illustration 
      *a
      Hook

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



9. REMOVE REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)


    B297552E01
  1. Disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR DOOR SCUFF PLATE LH


    B300785
  1. Disengage the 5 claws and guide and remove the rear door scuff plate LH.



11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the rear door opening trim weatherstrip LH.



12. REMOVE DECK BOARD ASSEMBLY
  1. Remove the deck board assembly.



13. REMOVE DECK FLOOR BOX LH
  1. Remove the deck floor box LH.



14. REMOVE DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Remove the package tray trim panel assembly.



16. REMOVE REAR DECK TRIM COVER


    B297727
  1. Remove the 2 clips.

  1. Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.



17. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Remove the bolt.



    B307773
  1. Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.



18. REMOVE REAR ABSORBER CAP LH


    B300796
  1. Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.



19. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY


    E286958E03
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *a
    Protective Tape



    E286959
  1. Remove the No. 1 luggage compartment light assembly as shown in the illustration.

  1. Disconnect the connector and remove the No. 1 luggage compartment light assembly.



20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


  1. Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.


    B300799E01


    Text in Illustration 
    *1
    Rear Seatback Hinge
    -
    -

  1. Remove the bolt and 2 screws.

  1. Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.



21. REMOVE RADIO SETTING CONDENSER

NOTICE:
When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.



    E282156
  1. Remove the bolt.

  1. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.



    E221953
  1. Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.



    E227453
  1. Using a screwdriver, bend back and break off the claw as shown in the illustration.

  1. Remove the terminal cover from the wire harness.

    NOTICE:
    1. Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
    2. Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
    3. Check for deformation of the terminal after the wire harness has been removed from the terminal cover.