AIR CONDITIONING SYSTEM > Steering Pad Switch Circuit |

| 1.INSPECT AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) |
Disconnect the G5 spiral cable with sensor sub-assembly connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G5-10 (AC1) - Body ground | Power switch off | Below 1 V |
| G5-10 (AC1) - Body ground | Power switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Spiral with Sensor Cable Sub-assembly) |
|
| ||||
| OK | |
| 2.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Disconnect the steering pad switch RH and spiral cable with sensor sub-assembly connectors.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z2-8 (EAU) - G5-4 (EAU) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z2-3 (AC1) - G5-10 (AC1) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable with sensor cable sub-assembly to the center position, rotate the spiral cable with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
| z2-8 (EAU) - G5-4 (EAU) | Always | Below 3 Ω |
| z2-3 (AC1) - G5-10 (AC1) | Always | Below 3 Ω |
| *a | Component without harness connected (SpiralC cable with sensor Cable Sub-assembly) |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH RH |
Remove the steering pad switch RH (Click here).
Measure the resistance according to the value(s) in the table below.

| *1 | TEMP + Switch | *2 | TEMP - Switch |
| *3 | R/F Switch | - | - |
| *a | Component without harness connected (Steering Pad Switch RH) | - | - |
| Tester Connection | Condition | Specified Condition |
| z2-3 (AC1) - z2-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| z2-3 (AC1) - z2-8 (EAU) | R/F switch pushed | 323 to 335 Ω |
| z2-3 (AC1) - z2-8 (EAU) | TEMP + switch pushed | 980 to 1020 Ω |
| z2-3 (AC1) - z2-8 (EAU) | TEMP - switch pushed | 3048 to 3172 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G5-4 (EAU) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G5-10 (AC1) - G33-3 (SWO) | Always | Below 1 Ω |
| G5-10 (AC1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||