DTC P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0ADC | 226 | Open or short to +B in the SMRB circuit |
|
| 1.READ VALUE USING INTELLIGENT TESTER (SMRB STATUS) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / SMRB Status.
Read the Data List.
| Tester Display | Switch Condition | Specified Condition |
| SMRB Status | Power switch on (IG) | OFF |
Turn the power switch off.
|
| ||||
| OK | |
| 2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors (Click here).
| *A | for LHD |
| *B | for RHD |
|
| ||||
| OK | |
| 3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR) |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid vehicle battery cover panel LH .
![]() |
Check the connector connections and contact pressure of the relevant terminals for the hybrid battery junction block assembly connector (Click here).
Install the No. 1 hybrid vehicle battery cover panel LH.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (SMRB VOLTAGE) |
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G80-4 (SMRB) - Body ground | Power switch on (IG) | Below 1 V |
| *a | Component with harness connected (Hybrid Vehicle Control ECU) |
Turn the power switch off.
|
| ||||
| OK | |
| 5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors (Click here).
| *A | for LHD |
| *B | for RHD |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND) |
Disconnect connector G80 from the hybrid vehicle control ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G80-4 (SMRB) - Body ground | Power switch off | 25.0 to 59.0 Ω |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control ECU) |
Connect the hybrid vehicle control ECU connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES) |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid vehicle battery cover panel LH .
![]() |
Disconnect connector M40 from the hybrid battery junction block assembly.
Disconnect connector G80 from the hybrid vehicle control ECU.
Turn the power switch ON (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G80-4 (SMRB) or M40-1 (SMRB) - Body ground | Power switch on (IG) | Below 1 V |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control ECU) |
| *b | Rear view of wire harness connector (to Hybrid Battery Junction Block Assembly) |
Turn the power switch off.
Connect the hybrid vehicle control ECU connectors.
Connect the hybrid battery junction block assembly connector.
Install the No. 1 hybrid vehicle battery cover panel LH.
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY) |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid vehicle battery cover panel LH .
Disconnect connector M40 from the hybrid battery junction block assembly.
Disconnect connector G80 from the hybrid vehicle control ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G80-4 (SMRB) - M40-1 (SMRB) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| G80-4 (SMRB) and M40-1 (SMRB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control ECU) |
| *b | Rear view of wire harness connector (to Hybrid Battery Junction Block Assembly) |
Connect the hybrid vehicle control ECU connector.
Connect the hybrid battery junction block assembly connector.
Install the No. 1 hybrid vehicle battery cover panel LH.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND) |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid vehicle battery cover panel LH .
Disconnect connector M40 from the hybrid battery junction block assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M40-2 (GND) - Body ground | Power switch off | Below 1 Ω |
| *a | Rear view of wire harness connector (to Hybrid Battery Junction Block Assembly) |
Connect the hybrid battery junction block assembly connector.
Install the No. 1 hybrid vehicle battery cover panel LH.
|
| ||||
| OK | |
| 10.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB) |
Check that the service plug grip is not installed.
Remove the hybrid battery junction block assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M40-1 (SMRB) - M40-2 (GND) | -40 to 80 °C (-40 to 176°F) | 25.0 to 59.0 Ω |
| *a | Component without harness connected (Hybrid Battery Junction Block Assembly) |
Install the hybrid battery junction block assembly.
|
| ||||
| OK | ||
| ||