FRONT DOOR LOCK > INSTALLATION |
| 1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the front door inside locking cable assembly as shown in the illustration.
![]() |
Engage the 3 claws as shown in the illustration.
| 2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the front door lock remote control cable assembly as shown in the illustration.
| 3. INSTALL FRONT DOOR LOCK ASSEMBLY |
Apply MP grease to the sliding parts of the front door lock assembly.
When reusing the front door lock assembly:
Install a new door lock wiring harness seal to the front door lock assembly.
![]() |
Insert the front door lock open rod to the front door lock assembly.
| *1 | Front Door Lock Open Rod |
Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.
Connect the connector.
| 4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder) |
![]() |
Install the front door outside handle cover with lock cylinder assembly.
Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.
![]() |
Install the hole plug.
| 5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Engage the guide.
Install the front door rear lower frame sub-assembly with the bolt.
| 6. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the front door No. 2 service hole cover.
| 8. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply new butyl tape to the front door panel.
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
![]() |
Attach the front door service hole cover according to the reference points on the front door panel.
| *a | Reference Point |
| 9. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
Install the front No. 2 speaker assembly with the 2 screws.
Connect the connector.
| 10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
![]() |
Engage the 8 clips.
![]() |
Install the front door trim board sub-assembly with the 3 screws.
![]() |
Engage the claw and close the cover.
| 11. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
Connect the connector.
![]() |
Engage the 4 guides and 10 claws to install power window regulator master switch assembly with front door armrest base panel.
| 12. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect the connector.
![]() |
Engage the 4 guides and 10 claws to install power window regulator switch assembly with front door armrest base panel.
| 13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 14. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 15. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side) |
| 16. CHECK POWER WINDOW CONTROL SYSTEM |