Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B307078
  1. Disengage the 10 claws and 4 guides.

  1. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.



5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B307079
  1. Disengage the 10 claws and 4 guides.

    1. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.



6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B307080E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B307081
  1. Remove the 3 screws.



    B307082
  1. Disengage the 8 clips and remove the front door trim board sub-assembly as shown in the illustration.



    B307083E01
  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable from the front door trim board sub-assembly.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly



7. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    E237142
  1. Disconnect the connector.

  1. Remove the 2 screws and front No. 2 speaker assembly.



8. REMOVE FRONT DOOR SERVICE HOLE COVER


    B308297
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any remaining butyl tape from the front door panel.



9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B307087
  1. Remove the front door No. 2 service hole cover.

  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the negative (-) auxiliary battery terminal and power window regulator master switch assembly.



    B307088
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B307089
  1. Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



10. REMOVE FRONT DOOR GLASS RUN


    B307092
  1. Remove the front door glass run.



11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B307095
  1. Remove the bolt.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly.



12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    B299844
  1. Remove the hole plug.



    B307098
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



13. REMOVE FRONT DOOR LOCK ASSEMBLY


    B307104E01
  1. Disconnect the connector.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Move the front door lock assembly downward and disconnect the front door lock open rod, and then remove the front door lock assembly.



  1. When reusing the front door lock assembly:



      B307105
    1. Remove the door lock wiring harness seal from the front door lock assembly.



14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307106
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



15. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307107
  1. Using a screwdriver, disengage the 3 claws as shown in the illustration.



    B307108
  1. Remove the front door inside locking cable assembly as shown in the illustration.