Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > INSTALLATION

for Preparation Click here



1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307165
  1. Install the rear door inside locking cable assembly as shown in the illustration.



    B307166
  1. Engage the 3 claws as shown in the illustration.



2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307167
  1. Install the rear door lock remote control cable assembly as shown in the illustration.



    B307168
  1. Engage the claw as shown in the illustration.



3. INSTALL REAR DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.

  1. Apply MP grease to the sliding parts of the rear door lock assembly.

  1. When reusing the rear door lock assembly:

    1. Install a new door lock wiring harness seal to the rear door lock assembly.



    B307170E01
  1. Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
    Text in Illustration 
    *1
    Release Plate

  1. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the rear door lock child protection cover.



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B307174E01
  1. Insert the rear door glass as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.

  1. Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.



5. INSTALL REAR DOOR QUARTER WINDOW GLASS


    B307171
  1. Install the rear door quarter window glass in the direction indicated by the arrow in the illustration.



6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Temporary install the rear door window division bar sub-assembly with the 2 bolts.

    NOTICE:
    Do not damage the rear door glass.

  1. Install the rear door window division bar sub-assembly with the 2 bolts and screw.



7. INSTALL REAR DOOR GLASS RUN


    B307143
  1. Install the rear door glass run.



8. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.

  1. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.



    B307175E01
  1. Attach the rear door service hole cover according to the reference points on the rear door panel.
    Text in Illustration 
    *a
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.



9. CONNECT REAR DOOR WEATHERSTRIP
  1. Connect the upper part of rear door weatherstrip.



10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307178E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



    B307182
  1. Engage the 7 clips.



    B308235
  1. Engage the clip.



    B307134
  1. Install the rear door trim board sub-assembly with the 3 screws.



    B307179
  1. Engage the claw and close the cover.



11. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
  1. Connect the connector.



    B307129
  1. Engage the 3 guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



12. INSTALL REAR DOOR FRAME GARNISH


    B307128
  1. Engage the guide.

  1. Engage the 2 clips and 3 claws to install the rear door frame garnish.



13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



14. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



15. CHECK POWER WINDOW CONTROL SYSTEM
(Click here)