Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE REAR DOOR FRAME GARNISH


    B307128
  1. Disengage the 2 clips and 3 claws.

  1. Disengage the guide and remove the rear door frame garnish.



5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B307129
  1. Disengage the 8 claws and 3 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307133E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B307134
  1. Remove the 3 screws.



    B308235
  1. Disengage the clip.



  1. pull the rear door trim board sub-assembly at the position indicated in the illustration and disengage the 7 clips in the order shown in the illustration.


    B307908

    NOTICE:
    Do not apply excessive force when pulling the rear door trim board sub-assembly.



    B307135E01
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly and remove the rear door trim board.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



7. DISCONNECT REAR DOOR WEATHERSTRIP
  1. Disconnect the upper part of rear door weatherstrip.



8. REMOVE REAR DOOR SERVICE HOLE COVER


    B307139
  1. Remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



9. REMOVE REAR DOOR GLASS RUN


    B307143
  1. Remove the rear door glass run.



10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Remove the 2 bolts and screw, and remove the rear door window division bar sub-assembly.



11. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B307150
  1. Remove the rear door quarter window glass as shown in the illustration.



12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B307145E02
  1. Slide the lower section of the rear door glass and disengage the rear door glass from the rear window regulator sub-assembly.

  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.



13. REMOVE REAR DOOR LOCK ASSEMBLY


    B307151
  1. Remove the rear door lock child protection cover.



    B307152E01
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.
    Text in Illustration 
    *1
    Release Plate



  1. When reusing the rear door lock assembly:



      B307153
    1. Remove the door lock wiring harness seal from the rear door lock assembly.



14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307154
  1. Using a screwdriver, disengage the claw as shown in the illustration.



    B307155
  1. Remove the rear door lock remote control cable assembly as shown in the illustration.



15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307156
  1. Using a screwdriver, disengage the 3 claws as shown in the illustration.



    B307157
  1. Remove the rear door inside locking cable assembly as shown in the illustration.