Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS



1. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting / Wireless Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Hazard Answer Back
      ON
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Lock Time
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp
      ON
      Wireless door lock buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol
      Level 5*1
      Level 7*2
      Wireless door lock buzzer volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0
      Main body ECU (Multiplex network body ECU)

      1. *1: w/ LED Headlight
      2. *2: w/o LED Headlight



2. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Entry Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body or Entry&Start / Utility / Customize / Wireless Door Lock, Entry&Start or Warning.

    5. Select the setting by referring to the table below.

      Wireless Door Lock 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Hazard Answer Back
      ON
      When the doors are locked by entry function, the hazard warning lights flash once.
      When the doors are unlocked by entry function, the hazard warning lights flash twice.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Auto Lock Time
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors.
      30 s, 60 s or 120 s
      Main body ECU (multiplex network body ECU)
      Wireless Buzzer Resp
      ON
      Function that sounds the answer-back buzzer when an entry lock or unlock operation is performed.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Wireless Buzzer Vol
      Level 5*1
      Level 7*2
      Buzzer answer back volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0
      Main body ECU (multiplex network body ECU)

      1. *1: w/ LED Headlight
      2. *2: w/o LED Headlight

      Entry&Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Park Wait Time (Waiting time to permit unlocking door after locking)
      2.5s
      Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.
      0.5s, 1.5s, 2.5s or 5s
      Certification ECU (smart key ECU assembly)
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the key must be in before the power switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Back Door opening Operation
      Long
      Function that opens the back door when the driver has the electrical key transmitter sub-assembly and presses back door opener switch assembly (unlock switch)
      Long, Twice or OFF
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Touch Activation Over Threshold
      Active
      The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.
      Active or Not Active
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Entry unlock mode switching function (manual operation)

    1. The following entry unlock modes can be selected when using the entry unlock mode switching function.

      1. All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.
      2. Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.

    2. When customizing through manual operation:

      1. Turn the power switch off.
      2. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.
      3. Check the current setting.

        HINT:
        1. The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.
        2. The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.


        Currently Selected Mode
        Answer-back (Wireless Buzzer)
        Answer-back (Buzzer in Combination Meter Assembly)
        All door unlock mode
        Buzzer sounds twice (short beeps)
        Buzzer sounds once
        Driver door unlock mode
        Buzzer sounds 3 times (short beeps)
        Buzzer sounds once
      4. Release the lock and unlock buttons of the electrical key transmitter sub-assembly.
      5. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

        HINT:
        Repeat the procedure as necessary to select the desired mode.

      6. Unlock the doors with the wireless operation, and then open any door

  1. Entry cancel function (manual operation)

    HINT:
    While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the power switch.


    1. The following functions are disabled when the smart entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Push start function
      3. Key lock-in prevention function
      4. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The power switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



3. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Start Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry&Start / Utility / Customize / Entry&Start or Warning.

    5. Select the setting by referring to the table below.

      Entry & Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the electrical key transmitter sub-assembly must be in before the power switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the power switch.


    1. The following functions are disabled when the smart entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Entry luggage compartment door open function
      3. Push-button start function
      4. Key lock-in prevention function
      5. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The power switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



4. CUSTOMIZE LIGHTING SYSTEM (INT)
  1. Customizing using the intelligent tester

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch to on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Illuminated Entry.

    5. Select the setting by referring to the table below.

      Illuminated Entry 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC) or on (IG).)
      7.5 s, 15 s or 30 s
      Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF
      ON
      Lights up the power switch illumination and personal light when the power switch is turned from on (ACC) or on (IG) to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the power switch illumination and personal light when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Room Light when Aprchd
      ON
      Lights up the power switch illumination and personal light when a key enters any actuation area around the doors.
      ON or OFF



5. CUSTOMIZE METER / GAUGE SYSTEM
  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting / Combination Meter / Warning.

    5. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.


      Warning 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Key Remind Sound
      Slow
      Function to change the cycle of the key remind warning buzzer
      Normal, Slow, Fast
      Combination meter assembly
      Driver Side Seatbelt Warning Buzzer*1
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*1
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      1. *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

  1. Customizing with the combination meter assembly

    HINT:
    1. Press and hold the DISP switch to enter an item.
    2. Briefly press the DISP switch to select an item.


    1. Turn the power switch on (IG).

    2. Enter the following menus: SETTINGS.

    3. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.


      Basic Settings 
      Combination meter assembly display
      Default
      Content
      Setting
      Relevant ECU
      Date
      -
      To adjust the date
      -
      Combination meter assembly
      Clock
      -
      To adjust the date
      -
      Combination meter assembly
      Clock Mode
      24H
      To select clock mode
      24H or 12H
      Combination meter assembly
      Steering Switch
      ON
      To select the steering pad switch display
      OFF or ON
      Combination meter assembly
      Language
      English
      To select the language
      English, Spanish, French
      Combination meter assembly

      Set ECO Savings 
      Combination meter assembly display
      Default
      Content
      Setting
      Relevant ECU
      Gasoline Price
      *1
      To select the gasoline price
      $/gal. or $/L
      Combination meter assembly
      Fuel Cons. Comparison
      *1
      To select the fuel consumption unit
      MPG or L/100km
      Combination meter assembly
      ECO Savings
      Basic
      To select the eco savings display setting
      Basic or Details
      Combination meter assembly
      *1: Changes according to the vehicle specification

      Menu Screen Selection 
      Combination meter assembly display
      Default
      Content
      Setting
      Relevant ECU
      ECO Savings Record
      OFF
      Display or not display eco savings record
      OFF or ON
      Combination meter assembly
      5 min. consumption
      OFF
      Display or not display 5 minutes fuel consumption
      OFF or ON
      Combination meter assembly
      Past Record
      OFF
      Display or not display fuel consumption record
      Monthly Avg. or Own Best
      Combination meter assembly

      Screen Off 
      Combination meter assembly display
      Default
      Content
      Setting
      Relevant ECU
      Basic Settings
      ON
      Display or not display the selected item
      -
      Combination meter assembly

      Set Clock 
      Combination meter assembly display
      Default
      Content
      Setting
      Relevant ECU
      Hour
      -
      To adjust the hour
      -
      Combination meter assembly
      Minute
      -
      To adjust the minute
      -
      Combination meter assembly
      Second
      -
      To adjust the second
      -
      Combination meter assembly

    4. Press and hold the DISP switch.

    5. Return to the item selection screen.



6. CUSTOMIZE SEAT BELT WARNING SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.
  4. These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Combination Meter / Utility / Customize / Warning.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer
      ON
      Function to sound the driver seat belt warning buzzer
      OFF/ON
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer
      ON
      Function to sound the front passenger seat belt warning buzzer
      OFF/ON

      HINT:
      This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.



7. CUSTOMIZE AIR CONDITIONING SYSTEM
  1. Customizing with the intelligent tester

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the intelligent tester.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Air Conditioner / Utility / Customize.

    5. Select the setting by referring to the table below.

      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Set Temperature Shift
      Normal
      Function to perform control with the shifted temperature versus the displayed temperature
      -2C, -1C, Normal, +1C, +2C
      Air Conditioning Amplifier Assembly
      Air Inlet Mode
      Automatic
      In case of turning the A/C on to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Foot/DEF Auto Mode
      ON
      Function to turn the airflow from FOOT/DEF on automatically when AUTO MODE is on
      ON or OFF
      Air Conditioning Amplifier Assembly
      Foot/DEF Automatic Blow Up Function
      ON
      Function to increase the blower level automatically when the defroster is on
      ON or OFF
      Air Conditioning Amplifier Assembly
      Ambient Temperature Shift
      Normal
      Function to display shifted ambient temperature versus actual ambient temperature
      -3C, -2C, -1C, Normal, +1C, +2C, +3C
      Air Conditioning Amplifier Assembly
      ECO MODE Cancel
      OFF
      Function to cancel the ECO mode drive when item is on
      OFF or ON
      Air conditioning amplifier assembly
      Noise and Vibration Reduction
      OFF
      Function to change speed of the compressor when item is on
      OFF or ON
      Air conditioning amplifier assembly
      Refrigerant Shortage Check
      ON
      Function to cancel the refrigerant shortage check (check performed during normal operation) when item is off
      ON or OFF
      Air Conditioning Amplifier Assembly
      Fan speed increment control
      Normal
      Function to define how fast the AC blower goes to target speed when first activating the AC
      Slow, Normal, Fast
      Air Conditioning Amplifier Assembly