Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.

  2. The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

    Function
    Control Master
    System Related
    Fail-safe Operation
    Driver Detectable
    DTC Detection
    (ECU that stored DTC)
    Air Conditioning Control
    1. Corrects engine speed, such as for idle up.
    2. Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal.
    3. Corrects engine coolant temperature map and changes compressor lock judgment value.
    Air conditioning amplifier assembly
    Power management control ECU
    Control is performed based on default coolant temperature of 80°C (176°F).
    -
    U0293
    (Air conditioning amplifier assembly)
    Destination Identification Control
    1. Changes air conditioning control pattern according to destination.
    Air conditioning amplifier assembly
    Main body ECU (Multiplex network body ECU)
    Maintains the latest state.
    -
    U0142
    (Air conditioning amplifier assembly)
    Ambient Temperature Correction Control
    1. Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal.
    Air conditioning amplifier assembly
    Combination meter assembly
    Control is performed based on default vehicle speed of 0 km/h (0 mph).
    1. Correction level for displayed ambient temperature declines.
    2. Correction level for outlet airflow declines.
    U0155
    (Air conditioning amplifier assembly)
    Air Conditioning Eco Mode Control
    1. Performs control in Eco mode using B_ECOMI.
    Air conditioning amplifier assembly
    Power management control ECU
    Maintains the latest state (Maintained in normal condition after reset).
    -
    U0101
    (Air conditioning amplifier assembly)
    Door Lock
    1. Controls key linked and automatic door lock/unlock function, key confinement prevention function, etc.
    Main body ECU (Multiplex network body ECU)
    1. Combination meter assembly
    2. ECM
    3. Power management control ECU
    1. Speed sensitive automatic lock control does not occur.
    2. Shift linked automatic lock control does not occur.
    3. Shift linked automatic unlock control does not occur.
    4. Automatic lock/unlock cannot be changed.
    -
    U0100
    U0101
    U0155
    (Main body ECU (Multiplex network body ECU))
    Illumination Control
    1. Turns on the interior lights when the smart key is brought near the vehicle.
    Main body ECU (Multiplex network body ECU)
    Smart key ECU assembly (Certification ECU)
    Interior lights turn off.
    -
    U0327
    (Main body ECU (Multiplex network body ECU))
    Entry Function/Wireless Control
    Smart key ECU assembly (Certification ECU)
    Main body ECU (Multiplex network body ECU)
    Entry lock/unlock control is not possible.
    -
    U0327
    (Main body ECU (Multiplex network body ECU))
    Drive Torque Control
    1. Controls the engine, MG1 and MG2 based on engine information received.
    Power management control ECU
    ECM
    Vehicle drives using only the motor.
    1. Displays messages on the multi-information display.
    2. MIL illuminates.
    U0100
    (Power management control ECU (Hybrid control system))
    Regenerative Operation
    1. Provides maximum amount of regeneration based on cooperative control with the ECB system.
    Power management control ECU
    Brake booster with master cylinder assembly (Skid control ECU)
    Regeneration is prohibited.
    1. Displays messages on the multi-information display.
    2. MIL illuminates.
    U0129
    (Power management control ECU (Hybrid control system))
    High Voltage Shut Off Control when the vehicle is damaged
    1. Receives the SRS collision detection signal and shuts off the system main relays.
    Power management control ECU
    Airbag sensor assembly
    Normal driving
    Displays messages on the multi-information display.
    U0151
    (Power management control ECU (Hybrid control system))
    HV System Power Processing
    1. Monitors whether IG2 is stuck ON based on IG2 information from the power management control ECU.
    Power management control ECU (Hybrid control system)
    Power management control ECU (Power management control CPU)
    1. Normal driving
    2. Power switch turns off 10 seconds after the vehicle is stopped and shift lever is moved to P.
    Displays messages on the multi-information display.
    U1107
    (Power management control ECU (Hybrid control system))
    Air Conditioning Control
    1. Sends a signal from the air conditioning amplifier assembly to the power management control ECU (HV CPU) and from the power management control ECU (HV CPU) to the inverter for the air conditioning system.
    Air conditioning amplifier assembly
    Power management control ECU
    Air conditioning cooling operation is stopped.
    -
    U0164
    (Power management control ECU)
    Engine Start/Stop Switch (Power Source Mode Change)
    1. Using start/stop switch signal as trigger, changes power source mode automatically and requests starter operation when conditions are met.
    Power management control ECU (Power management control CPU)
    1. Main body ECU (Multiplex network body ECU)
    2. Combination meter assembly
    3. Power management control ECU (Hybrid control system)
    None
    -
    U0140
    U0155
    U0293
    Power management control ECU (Power management control CPU)
    Cruise Control
    1. Calculates demand drive force to maintain vehicle speed.
    Power management control ECU
    Brake booster with master cylinder assembly (Skid control ECU)
    Cruise control is canceled.
    1. Displays messages on the multi-information display.
    2. Master warning light turns on.
    U0122
    (Power management control ECU)
    Charge Control
    1. Performs idle up according to charging request.
    Power management control ECU
    Air conditioning amplifier assembly
    Idle up according to charging request is not performed.
    Taillights flicker and blower airflow changes.
    -
    Power Steering Control
    1. Calculates assist current according to torque sensor value and vehicle speed and drives motor.
    Power steering ECU assembly
    1. Power management control ECU
    2. Brake booster with master cylinder assembly (Skid control ECU)
    1. Control is performed based on default assist current for a vehicle speed of 70 km/h (43 mph).
    2. Drivability degrades (compensation control using steering angle is stopped).
    EPS warning light illuminates.
    U0129
    U0293
    (Power steering ECU assembly)
    Steering Assist Calculation
    1. Changes assist force based on vehicle speed.
    Power steering ECU assembly
    Brake booster with master cylinder assembly (Skid control ECU)
    Control continues based on a default speed of 70 km/h (43 mph) because vehicle speed is unrecognizable.
    EPS warning light illuminates.
    U0129
    U0293
    (Power steering ECU assembly)
    Steering Assist Start Judgment
    Power steering ECU assembly
    1. Power management control ECU
    2. Brake booster with master cylinder assembly (Skid control ECU)
    When a communication stop of power management control ECU communication occurs:
    1. Assist starts when the vehicle speed is 0.1 km/h (0.06 mph) or more.
    When a communication stop of the power management control ECU or brake booster with master cylinder assembly (skid control ECU) occurs:
    1. Control continues based on a default vehicle speed of 70 km/h (43 mph).
    EPS warning light illuminates.
    U0129
    U0293
    (Power steering ECU assembly)
    Assist Map Selection
    1. Selects proper assist map according to destination, engine type, etc.
    Power steering ECU assembly
    Power management control ECU
    Default map is used to assist because proper assist map cannot be selected. (Steering feel may be different.)
    EPS warning light illuminates.
    C1581
    (Power steering ECU assembly)
    Steering Assist Compensation Control
    1. Provides steering assist with compensation amount based on vehicle speed.
    Power steering ECU assembly
    Brake booster with master cylinder assembly (Skid control ECU)
    Control is performed based on a default vehicle speed of approximately 70 km/h (43 mph).
    EPS warning light illuminates.
    U0129
    (Power steering ECU assembly)
    Steering/Steering Angle Sensor initialization and zero point learning
    1. Performs steering/ steering angle sensor initialization and zero point learning.
    Power steering ECU assembly
    1. Brake booster with master cylinder assembly (Skid control ECU)
    2. Spiral cable with sensor sub-assembly (Steering angle sensor)
    3. Airbag sensor assembly (built-in type yaw rate sensor)
    Steering initialization and zero point learning are not performed.
    EPS warning light illuminates.
    U0129
    (Power steering ECU assembly)
    Entry Function
    1. Entry lock/unlock, entry luggage compartment open.
    2. Warning.
    3. Performs entry illumination (Interior illumination etc).
    1. Main body ECU (Multiplex network body ECU)
    2. Smart key ECU assembly (Certification ECU)
    1. Main body ECU (Multiplex network body ECU)
    2. Combination meter assembly
    Entry unlock is performed again.
    1. Entry lock/unlock or entry luggage compartment open does not operate.
    2. Warning functions (Key confinement, Key not in vehicle, Key reminder etc.) do not operate, Key confinement prevention control does not operate.
    3. Entry illumination does not operate.
    U0327
    (Main body ECU (Multiplex network body ECU))
    U0142
    U0155
    (Smart key ECU assembly (Certification ECU))
    Wireless Function
    1. Locks and unlocks doors etc. via remote operation.
    Main body ECU (Multiplex network body ECU)
    Smart key ECU assembly (Certification ECU)
    Wireless lock, unlock and luggage compartment opener do not operate.
    -
    U0142
    (Smart key ECU assembly (Certification ECU))
    Power Switch Backlighting Control
    1. Turns on/off power switch illumination linked with interior lights etc.
    Smart key ECU assembly (Certification ECU)
    Main body ECU (Multiplex network body ECU)
    Power switch backlighting does not illuminate according to interior lights operation.
    -
    U0142
    (Smart key ECU assembly (Certification ECU))
    Vehicle Speed Display
    Combination meter assembly
    Brake booster with master cylinder assembly (Skid control ECU)
    Speedometer is controlled based on a default vehicle speed of 0 km/h (0 mph).
    1. The needle points at 0 km/h (0 mph).
    2. Drive monitor calculation is stopped.
    U0129
    (Combination meter assembly)
    HV Indicator Display
    Combination meter assembly
    Power management control ECU
    HV indicator turns off.
    -
    U0100
    (Combination meter assembly)
    Airbag
    (Airbag warning light control)
    Combination meter assembly
    Airbag sensor assembly
    None
    Airbag warning light illuminates.
    U0151
    (Combination meter assembly)
    EPS Warning
    (EPS warning light control)
    Combination meter assembly
    Power steering ECU assembly
    None
    EPS warning light illuminates.
    U0131
    (Combination meter assembly)
    SLIP Warning
    (SLIP warning light control)
    Combination meter assembly
    Brake booster with master cylinder assembly (Skid control ECU)
    None
    SLIP indicator illuminates.
    U0129
    (Combination meter assembly)
    HV Drive Guide Display
    1. Displays EV conditions.
    Combination meter assembly
    ECM
    EV condition display turns off.
    -
    U0100
    (Combination meter assembly)
    Anti-lock Brake System Control
    1. Prevents the wheels from locking during sudden stops.
    Brake booster with master cylinder assembly (Skid control ECU)
    Airbag sensor assembly (built-in type yaw rate sensor)
    1. During control: When backup control (stabilizing the vehicle) is complete, the system changes to normal braking and prohibits control.
    2. Not during control: Control cannot be performed.
    1. Brake warning light (red) illuminates.
    2. ABS warning light illuminates.
    3. SLIP indicator illuminates.
    4. Brake warning light (yellow) illuminates.
    U0073
    U0123
    U0124
    (Brake booster with master cylinder assembly (Skid control ECU))
    Vehicle Stability Control/Traction Control
    1. Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when accelerating from rest.
    Brake booster with master cylinder assembly (Skid control ECU)
    1. Power management control ECU
    2. Airbag sensor assembly (built-in type yaw rate sensor)
    3. Spiral cable with sensor sub-assembly (Steering sensor)
    1. During control: When backup control (stabilizing the vehicle) is complete, the system changes to normal braking and prohibits control.
    2. Not during control: Control cannot be performed.
    1. Brake warning light (red) illuminates.
    2. ABS warning light illuminates.
    3. SLIP indicator illuminates.
    4. Brake warning light (yellow) illuminates.
    U0073
    U0123
    U0124
    U0126
    U0293
    (Brake booster with master cylinder assembly (Skid control ECU))
    HAC3 Control
    1. Maintains the brake hydraulic pressure to the 4 wheels for 2 seconds with the brake pedal released when starting off on an uphill.
    Brake booster with master cylinder assembly (Skid control ECU)
    1. Power management control ECU
    2. Spiral cable with sensor sub-assembly (Steering sensor)
    3. Airbag sensor assembly (built-in type yaw rate sensor)
    1. When control is being performed: Once control (depressurization control) has completed, further hill-start assist control is prohibited.
    2. When control is not being performed: Hill-start assist control does not start.
    1. Brake warning light (red) illuminates.
    2. ABS warning light illuminates.
    3. SLIP indicator illuminates.
    4. Brake warning light (yellow) illuminates.
    U0073
    U0123
    U0124
    U0126
    U0293
    (Brake booster with master cylinder assembly (Skid control ECU))
    Hybrid Regenerative Operation
    1. Regenerative cooperative control with the HV system.
    Brake booster with master cylinder assembly (Skid control ECU)
    1. Power management control ECU
    2. Airbag sensor assembly (built-in type yaw rate sensor)
    1. When control is being performed: HV cooperative control is continued based on the latest value and gradually decreased. After this, HV cooperative control is prohibited.
    2. When control is not being performed: HV cooperative control does not start.
    1. Brake warning light (red) illuminates.
    2. ABS warning light illuminates.
    3. SLIP indicator illuminates.
    4. Brake warning light (yellow) illuminates.
    U0073
    U0123
    U0124
    U0293
    (Brake booster with master cylinder assembly (Skid control ECU))