Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL

UPPER INSTRUMENT PANEL > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work (Click here)



2. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B301680E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B301681
  1. Using a moulding remover, disengage the 8 clips and claw.

    NOTICE:
    Do not use a moulding remover to an area other than that shown in the illustration. Using a moulding remover in an area other than that shown in the illustration may result in deformation or damage to related parts.

  1. Disconnect the connector and remove the center instrument cluster finish panel sub-assembly.



5. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)


    B301683
  1. Disengage the 3 clips and remove the No. 2 instrument panel register assembly.



6. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for RHD)


    B297457
  1. Disengage the 3 clips and remove the No. 1 instrument panel register assembly.



7. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B301684E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B301685
  1. Using a moulding remover, disengage the 12 clips and 10 guides to remove the instrument cluster finish panel garnish.



8. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    B301687
  1. Disengage the claw and 4 clips to remove the center instrument panel register assembly.



9. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B301688
  1. Using a clip remover, remove the 2 clips.



    B301689
  1. Disengage the 4 claws and 9 guides and remove the instrument cluster finish panel sub-assembly.



10. REMOVE COMBINATION METER ASSEMBLY


    E244444
  1. Remove the 2 screws.



    E244445
  1. Disengage the 3 clips as shown in the illustration.



    E244446
  1. Disconnect the 2 connectors.

  1. Disengage the clamp and remove the combination meter assembly.



11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the front door opening trim weatherstrip LH.



12. REMOVE FRONT PILLAR GARNISH LH


    E276150E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Let the front pillar garnish LH hang down from the front pillar garnish clip.



    E276147E01
  1. Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip 90° in the direction indicated by the arrow (1) shown in the illustration.
    Text in Illustration 
    *a
    90°
    *b
    Protective Tape

  1. Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip.

    NOTICE:
    1. If the front pillar garnish clip is not removed from the vehicle body and is not damaged, the front pillar garnish clip can be reused.
    2. If the front pillar garnish clip is removed from the vehicle body, make sure to replace it with a new one.

  1. Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.



    B300790E01
  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly

    1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Disconnect the front door opening trim weatherstrip RH.



14. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



15. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B300245E01
  1. Slide the slider to release the lock, and then disconnect the connector.
    Text in Illustration 
    *a
    Slider

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



16. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY


  1. Remove the bolt <A>.


    B301690E01


    Text in Illustration 
    *1
    Bolt <A>
    *2
    Screw <C>

  1. Remove the screw <C>.

  1. Using a clip remover, remove the 2 clips.



  1. Pull the upper instrument panel assembly in the direction indicated by the arrow (1) to disengage the 7 clips.


    B301692E01

  1. Pull the upper instrument panel assembly in the direction indicated by the arrow (2) to disengage the 5 guides and remove the upper instrument panel assembly.