Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL

LOWER INSTRUMENT PANEL > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY
(Click here)


3. REMOVE NO. 1 SWITCH HOLE BASE


  1. for LHD:



      B307669
    1. Disengage the 4 claws and 2 clips as shown in the illustration.

    2. Disconnect each connector and remove the No. 1 switch hole base.



  1. for RHD:



      B297481
    1. Disengage the 2 claws and 3 clips.

    2. Disconnect each connector and remove the No. 1 switch hole base.



4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH (for LHD)


    B307671
  1. Disengage the 9 claws and remove the lower instrument panel finish panel LH as shown in the illustration.



5. REMOVE LOWER STEERING COLUMN COVER


    C248042
  1. Remove the 3 screws.



    C256915
  1. Disengage the 4 claws and remove the lower steering column cover.



6. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



  1. for LHD:



      B296311
    1. Remove the 4 bolts.



    2. B296312
    3. Disengage the 7 claws and the 3 guides to remove the lower No. 1 instrument panel airbag assembly.

      NOTICE:
      When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



  1. for RHD:



      B296315
    1. Remove the 4 bolts.



    2. B300206
    3. Disengage the 9 claws and the 2 guides to remove the lower No. 1 instrument panel airbag assembly.

      NOTICE:
      When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



    B296313E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

  1. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



7. REMOVE NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


    B307673
  1. Disengage the clamp.



    B307674
  1. Disengage the 2 claws as shown in the illustration.



    B307676
  1. Disengage the guide and remove the No. 6 heater to register duct assembly as shown in the illustration.



8. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    B307678
  1. Remove the 4 screws <C> and radio tuner opening cover with bracket.



9. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


    E244891
  1. Remove the 4 screws.



    E244892
  1. Disengage the 2 guides and pull the radio receiver assembly with bracket toward the rear of the vehicle.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.



10. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL GARNISH


  1. for LHD:



      B307679
    1. Disengage the 3 claws, 8 clips and 3 guides, and remove the lower instrument cluster finish panel garnish as shown in the illustration.



  1. for RHD:



      B297484
    1. Disengage the 2 claws, 8 clips and 4 guides, and remove the lower instrument cluster finish panel garnish as shown in the illustration.



11. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E238271
  1. Disengage the 4 clips.

  1. Disconnect the connector and remove the air conditioning control assembly.



12. REMOVE ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)


    E238260
  1. Insert a screwdriver into the position shown in the illustration to disengage the 2 claws.



    E238261
  1. Disconnect the connector and aspirator and remove the room temperature sensor (cooler thermistor).



13. REMOVE REAR CONSOLE BOX COVER


    B297443
  1. Using a moulding remover, disengage the 4 claws.

  1. Disconnect each connector and remove the rear console box cover.



14. REMOVE UPPER CONSOLE PANEL


    B307699
  1. Disengage the 2 claws and 6 clips and remove the upper console panel.



15. REMOVE FRONT CONSOLE BOX


  1. Disengage the 2 claws, 4 clips and 4 guides to remove the front console box as shown in the illustration.


    B436117



16. REMOVE CONSOLE BOX PLATE


    B297439
  1. Remove the console box plate.



17. REMOVE REAR CONSOLE BOX ASSEMBLY


    B307703
  1. Remove the 3 bolts and 2 screws.



    B307704
  1. Disengage the 2 clips and remove the rear console box assembly.



18. REMOVE INSTRUMENT PANEL BOX ASSEMBLY


  1. for LHD:



      B307680
    1. Disengage the 3 clamps.



    B307681
  1. Remove the screw <D>.



    B307682E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B307683E01
  1. Using a moulding remover, pull the instrument panel box in the direction indicated by the arrow (1) to disengage the 5 claws (A).
    Text in Illustration 
    *a
    Claw (A)
    *b
    Claw (B)

  1. Pull the instrument panel box in the direction indicated by the arrow (2) to disengage the 2 claws (B) and remove the instrument panel box assembly.



19. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B307685E01
  1. Disengage the claw and release the glove compartment door stopper sub-assembly.
    Text in Illustration 
    *1
    Glove Compartment Door Stopper Sub-assembly

  1. Slightly bend the stopper (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.



    B307687E01
  1. Open the glove compartment door assembly to approximately 55° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.
    Text in Illustration 
    *a
    Closed
    *b
    Open Approximately 55°

    NOTICE:
    Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.



20. REMOVE FRONT DOOR SCUFF PLATE LH


    B300786
  1. Disengage the 8 claws and remove the front door scuff plate LH.



21. REMOVE COWL SIDE TRIM BOARD LH


    B300787
  1. Remove the clip.

  1. Disengage the clip and remove the cowl side trim board LH.



22. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



23. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure as for the LH side.



24. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B307689
  1. Disengage the claw and 2 guides and disconnect the hood lock control lever sub-assembly.



25. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)


  1. Disengage each clamp.


    B307690E01


    Text in Illustration 
    *1
    DLC3
    -
    -

  1. Disconnect each connector.

  1. Disengage the 2 claws to disconnect the DLC3.



  1. Remove the 2 bolts <A>, 7 screws <C> and screw <B> and lower instrument panel sub-assembly.


    B307691E01


    Text in Illustration 
    *1
    Bolt <A>
    *2
    Screw <B>
    *3
    Screw <C>
    -
    -



26. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)


  1. Disengage each clamp.


    B297506E01


    Text in Illustration 
    *1
    DLC3
    -
    -

  1. Disconnect each connector.

  1. Disengage the 2 claws to disconnect the DLC3.



  1. Remove the 2 bolts <A>, 7 screws <C> and screw <B> and lower instrument panel sub-assembly.


    B386800E01


    Text in Illustration 
    *1
    Bolt <A>
    *2
    Screw <B>
    *3
    Screw <C>
    -
    -