Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3107-213    Lost Communication with Airbag System Control Module

for Preparation Click here


DESCRIPTION

  1. The power management control ECU detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3107
213
Short to GND in the communication circuit
  1. Wire harness or connector
  2. Airbag sensor assembly
  3. Power management control ECU

WIRING DIAGRAM


A254875E10


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 15 seconds or more.

1.CHECK DTC OUTPUT (SRS AIRBAG)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body / SRS Airbag / DTC.

  1. Check if DTCs are output.

Result:
Result
Proceed to
Airbag system DTCs are not output.
A
Airbag system DTCs are output.
B

  1. Turn the power switch off.



B
GO TO DTC CHART (AIRBAG SYSTEM) (Click here)
A


2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)
  1. Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.

  1. Turn the power switch on (READY).



    A216762E10
  1. Measure the waveform.
    Item
    Contents
    Terminal
    G18-14 (GSW2) - G18-25 (E1)
    Equipment Setting
    5V/DIV., 500ms/DIV.
    Condition
    Power switch on (READY)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    Text in Illustration  
    *a
    Component with harness connected
    (Airbag Sensor Assembly)

  1. Turn the power switch off.



B
Go to step 6
A


3.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


4.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3107-213 is not output.
    A
    P3107-213 is output.
    B

  1. Turn the power switch off.



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A


5.CHECK FOR INTERMITTENT PROBLEMS
(Click here)


NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

6.CHECK AIRBAG SENSOR ASSEMBLY
  1. Disconnect connector G18 from the airbag sensor assembly.



    A257822E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G18-14 (GSW2) - G18-25 (E1)
    Power switch off
    10 kΩ or higher

    Text in Illustration  
    *a
    Component without harness connected
    (Airbag Sensor Assembly)

  1. Connect the airbag sensor assembly connector.



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
  1. Disconnect connector G57 from the power management control ECU.

  1. Disconnect connector G18 from the airbag sensor assembly.



    A216764E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) or G18-14 (GSW2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration  
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Rear view of wire harness connector
    (to Airbag Sensor Assembly)

  1. Connect the airbag sensor assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)