DTC P3107-213 Lost Communication with Airbag System Control Module |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P3107 | 213 | Short to GND in the communication circuit |
|

| 1.CHECK DTC OUTPUT (SRS AIRBAG) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / SRS Airbag / DTC.
Check if DTCs are output.
| Result | Proceed to |
| Airbag system DTCs are not output. | A |
| Airbag system DTCs are output. | B |
Turn the power switch off.
|
| ||||
| A | |
| 2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM) |
Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.
Turn the power switch on (READY).
![]() |
Measure the waveform.
| Item | Contents |
| Terminal | G18-14 (GSW2) - G18-25 (E1) |
| Equipment Setting | 5V/DIV., 500ms/DIV. |
| Condition | Power switch on (READY) |
| Result | Proceed to |
| The waveform appears as shown in the illustration. | A |
| The waveform differs from the one shown in the illustration. | B |
| *a | Component with harness connected (Airbag Sensor Assembly) |
Turn the power switch off.
|
| ||||
| A | |
| 3.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
| NEXT | |
| 4.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
| P3107-213 is not output. | A |
| P3107-213 is output. | B |
Turn the power switch off.
|
| ||||
| A | |
| 5.CHECK FOR INTERMITTENT PROBLEMS |
|
| ||||
| OK | ||
| ||
| 6.CHECK AIRBAG SENSOR ASSEMBLY |
Disconnect connector G18 from the airbag sensor assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G18-14 (GSW2) - G18-25 (E1) | Power switch off | 10 kΩ or higher |
| *a | Component without harness connected (Airbag Sensor Assembly) |
Connect the airbag sensor assembly connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY) |
Disconnect connector G81 from the hybrid vehicle control ECU.
Disconnect connector G18 from the airbag sensor assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G81-14 (ABFS) or G18-14 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control ECU) |
| *b | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Connect the airbag sensor assembly connector.
Connect the hybrid vehicle control ECU connector.
|
| ||||
| OK | ||
| ||