Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3108-536    Lost Communication with A/C System Control Module

for Preparation Click here


DESCRIPTION

  1. The hybrid vehicle control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3108
536
A/C inverter malfunction
  1. Wire harness or connector
  2. Compressor with motor assembly
  3. Hybrid vehicle control ECU

WIRING DIAGRAM


A254877E27


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Wait for 30 seconds or more with the power switch on (READY) and the air conditioning turned off.
  2. Turn the air conditioning on and wait for 30 seconds or more.

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A279820E01
  1. Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors (Click here).
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)


    A267470E01
  1. Check the connection of connector C22 of the compressor with motor assembly.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)
  1. Disconnect connector C22 from the compressor with motor assembly.



    A211448E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-5 (GND) - Body ground
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-6 (IG1) - C22-5 (GND)
    Power switch on (IG)
    11 to 14 V

    NOTICE:
    Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the compressor with motor assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3108-536 is output.
    A
    P3108-536 is not output.
    B

  1. Turn the power switch off.



B
Go to step 8
A


5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
  1. Disconnect connector A72 from the hybrid vehicle control ECU.

  1. Disconnect connector C22 from the compressor with motor assembly.

  1. Turn the power switch on (IG).



    A344359E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CLK) - Body ground
    Power switch on (IG)
    Below 1 V
    A72-8 (ETI) - Body ground
    Power switch on (IG)
    Below 1 V
    A72-9 (ITE) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)
    *b
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CLK) - C22-1 (CLK)
    Power switch off
    Below 1 Ω
    A72-8 (ETI) - C22-3 (DOUT)
    Power switch off
    Below 1 Ω
    A72-9 (ITE) - C22-2 (DIN)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CLK) or C22-1 (CLK) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A72-8 (ETI) or C22-3 (DOUT) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A72-9 (ITE) or C22-2 (DIN) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

  1. Connect the compressor with motor assembly connector.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HYBRID VEHICLE CONTROL ECU
  1. Disconnect connector C22 from the compressor with motor assembly.



    A211448E27
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-3 (DOUT) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-1 (CLK) - Body ground
    Power switch on (IG)
    11 to 14 V
    C22-2 (DIN) - Body ground
    Power switch on (IG)
    11 to 14 V
    C22-3 (DOUT) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the compressor with motor assembly connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK


7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
  1. Disconnect connector A72 from the hybrid vehicle control ECU.



    A250971E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CLK) - Body ground
    Power switch off
    10 kΩ or higher
    A72-9 (ITE) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-8 (ETI) - Body ground
    Power switch on (IG)
    11 to 14 V
    A72-10 (CLK) - Body ground
    Power switch on (IG)
    Below 1 V
    A72-9 (ITE) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
  1. Disconnect connector A72 from the hybrid vehicle control ECU.

  1. Disconnect connector C22 from the compressor with motor assembly.

  1. Turn the power switch on (IG).



    A344359E05
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (STB) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)
    *b
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (STB) - C22-4 (STBI)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (STB) or C22-4 (STBI) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

  1. Connect the compressor with motor assembly connector.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HYBRID VEHICLE CONTROL ECU
  1. Disconnect connector C22 from the compressor with motor assembly.



    A211448E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-4 (STBI) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-4 (STBI) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the compressor with motor assembly connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK


10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
  1. Disconnect connector A72 from the hybrid vehicle control ECU.



    A250971E45
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (STB) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (STB) - Body ground
    Power switch on (IG)
    11 to 14 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)